Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Toshiba e-Studio 6560C — Trang 7/44

Code: C481

Description: IH drive circuit abnormality
Causes: IH board LGC board
Remedy: IH board • Connector check • Harness check LGC board • Connector check (CN305) • Harness check Status counter 1. [0], [8] Power ON. 2. Key in “2002”, then press [START]. 3. Change the current status counter value (08-2002) “15” to “0”.

Code: C490

Description: IH circuit abnormality / IH coil abnormality
Causes: IH board LGC board
Remedy: Power supply • Check if the power voltage is normal.(Is the voltage during the operation ±10% of the rated voltage?) • Connector check (CN403, CN409) IH board • Connector check • Harness check Fuser unit • Unit check • Connector check • Harness check Status counter 1. [0], [8] Power ON. 2. Key in “2002”, then press [START]. 3. Change the current status counter value (08-2002) “17” to “0”.

Code: C4B0

Description: Fuser unit counter abnormality
Causes: LGC board
Remedy: LGC board • SRAM check • Board check Status counter 1. [0], [8] Power ON. 2. Key in “2002”, then press [START]. 3. Change the values “72” or above, or “4” of the status counter (08-2002) to “0”

Code: C4B1

Description: Fuser unit voltage judgment abnormality
Causes: Fuser unit LGC board Switching regulator IH board
Remedy: Fuser unit • Unit check • Connector check • Harness check LGC board • Connector check (CN305, CN306, CN330) • Board check Switching regulator • Connector check (CN404) • Harness check IH board • Connector check • Board check

Code: C4E0

Description: Fuser pressure release abnormality
- Though the pressure roller is released, its position cannot be detected.
Causes: Pressure roller contact/release detection sensor Pressure roller contact/release clutch LGC board
Remedy: Pressure roller contact/release detection sensor(S48) • Sensor check (Perform the input check: 03-[ALL]OFF/[3]/[F]) • Connector check • Harness check Pressure roller contact/release clutch(CLT1) • Clutch check (Perform the output check: 03-273) • Connector check • Harness check Fuser unit • Unit check • Connector check • Harness check • Check that 2 dowels are securely fitted into the holes of the fuser drive unit. LGC board • Connector check (CN306, CN311) • Board check

Code: C4E1

Description: Fuser pressure contact abnormality
- Though the pressure roller is contacted, its position cannot be detected.
Causes: Pressure roller contact/release detection sensor Pressure roller contact/release clutch LGC board
Remedy: Pressure roller contact/release detection sensor(S48) • Sensor check (Perform the input check: 03-[ALL]OFF/[3]/[F]) • Connector check • Harness check Pressure roller contact/release clutch(CLT1) • Clutch check (Perform the output check: 03-273) • Connector check • Harness check Fuser unit • Unit check • Connector check • Harness check • Check that 2 dowels are securely fitted into the holes of the fuser drive unit. LGC board • Connector check (CN306, CN311) • Board check

Code: C4E2

Description: Fuser belt rotation detection sensor abnormality
- The fuser belt does not rotate or incorrectly rotates.
Causes: Fuser belt rotation detection sensor Detection plate (rotor) Dirty/damaged Fuser roller Deformed/damaged Heat pipe roller bearing Locked (Rotation failure) Bushing Worn Drive plate Bend section broken Gear Teeth damaged, worn LGC board
Remedy: Fuser unit • Fuser belt rotation detection sensor check (Input check: 03-[FAX]ON/[4]/[F]) • Connector check in the fuser belt rotation sensor • Harness check in the fuser belt rotation sensor • Detection plate (rotor) check • Grease check in the gear (shaft / tooth flank) • Fuser roller check • Check that the C-ring in the pressure roller does not come off. • Check that the bearing in the heat pipe roller rotates properly. • Fuser unit installation check (Check that the screws fixing the fuser unit are not loose.) Fuser drive unit • Bushing check • Check that the drive unit is correctly installed (2 dowels). • Check that the drive metal plate is not broken. • Check that the gear is not damaged or worn. • One-way clutch check • Grease check in the gear (shaft / tooth flank) LGC board • Connector check (CN306) • Board check

Code: C550

Description: RADF I/F error: Communication error has occurred between the RADF and the scanner.
Causes: RADF board Replace the RADF board, and then perform the automatic adjustment for the original reading start sensor (05-3210). SLG board
Remedy: RADF board • Connector check (CN70, CN71) • Harness check • Board check SLG board • Connector check • Board check
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie