• Code: 07-500
• Description: Manual Feed Slot Paper Empty Fault The Manual Feed Slot Empty Sensor failed to detect paper in the Manual Feed Slot.
• Remedy: Check the Manual Feed Slot Empty Sensor actuator. The actuator moves freely and is undamaged. Replace the Empty Sensor Actuator. Block and clear the Manual Feed Slot Empty Sensor. The sensor signal changes. Replace the Tray Empty Sensor. Check the circuit of the Tray Empty Sensor.

• Code: 07-530
• Description: Paper Feed Fault - Manual Feed Slot The lead edge was not detected by the Paper Feed Sensor.
• Remedy: Check the position of the jammed sheet. The lead edge reached the Retard Roll. Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 102-Sensor, Feed Sens] to block and clear the Feed Sensor. The sensor is OK. Replace the Feed Sensor . From the EDC menu, select: [101-Clutch, Registration] to engage the drive to pick up paper from tray 1. The clutch engages. Replace the Tray 1 Pick up (Feed) Clutch . Perform SCP Final Actions. Check the Paper Feed actuator. The actuator moves freely is undamaged. Replace the Paper Feed actuator . Inspect the Paper Feed Sensor for damage. The sensor is OK. Replace the Paper Feed Sensor . Check the circuit of the Paper Feed Sensor. .

• Code: 08-100
• Description: Paper Feed Fault - Tray 1 The lead edge was not detected by the Paper Feed Sensor.
• Remedy: Check the Tray 1 Pick up Sensor Actuator. The Actuator moves freely. Replace the Tray 1 Pick up Sensor Actuator. Check the position of the jammed sheet. The lead edge reached the Retard Roll. (Figure 1.) Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 101-Clutch, Tray 1 Pick up] to engage the drive to pick up paper from tray 1 The clutch engages. Replace the Tray 1 Pick up (Feed) Clutch . Check the Paper Feed Actuator. The actuator moves freely. Replace the Paper Feed Actuator. In Diagnostics Mode. Select: [102-Sensor, Feed Sens] to block and clear the Paper Feed Sensor. The signal changes. Replace the Paper Feed Sensor . Perform SCP Final Actions. Check the circuit of the Paper Feed Sensor.

• Code: 08-500
• Description: Paper Jam in Exit Area Fault The machine has detected a paper jam in the Exit Area.
• Remedy: Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 102-Sensor, Feed Sens] to test the Exit Sensor. The Exit Sensor is OK. Replace the Exit Sensor. In Diagnostics, go to [102-Sensor, Registration] to activate and deactivate the Registration Sensor. The signal changes. Replace the Registration sensor. Inspect the Exit Roller and Drives for wear or damage. Replace if needed.

• Code: 08-600
• Description: Paper Jam in Duplex Area Fault The machine has detected a paper jam in the Duplex Area.
• Remedy: Check the Exit Sensor Actuator. The actuator moves freely. Replace the Exit Sensor Actuator. Enter Diagnostics (EDC) Mode. Select: [DC330 Component Control, 102-Sensor, Out Bin Exit Sens] to test the Exit Sensor. The sensor is OK. Replace the Exit Sensor. Check the following parts for wear or damage and replace if needed: • Duplex Paper Guide • Duplex Gate • Duplex Gate Spring • Duplex Gate Mounting • Paper Guide on Rear Cover Make certain that the Duplex Gate is seated correctly and moves freely without binding.

• Code: 08-700
• Description: Output Tray Full Fault The Output Tray Full Sensor has detected that the Output Tray is full.
• Remedy: Enter Diagnostic (EDC) Mode. Select: [DC330 Component Control, 102-Sensor, Out Bin Full] to test the Out Bin Full Sensor. The signal changes. • Check that the sensor connector is firmly seated. • Replace the Out Bin Full Sensor. Check actuator for binding. If the problem is intermittent, replace the Out Bin Full Sensor Actuator.

• Code: 09-100
• Description: Toner Cartridge Near End of Life Fault The Toner Cartridge life is less than 10%.
• Remedy: 1. Check the remaining life of the Toner Cartridge by using one of the methods listed below: • Print a Supplies Information Report. [GP 2] • Open Easy Printer Manager, check Toner Life. • Open the CWIS application. Select; [Status, Supplies, Print Cartridge]. 2. Check the remaining life of the Toner Cartridge. 3. If the Toner Cartridge has reached end of life, switch Off the power and replace the Toner Cartridge.

• Code: 09-300
• Description: Imaging Unit Near End of Life Fault The Imaging Unit life is less than 10%.
• Remedy: 1. Check the remaining life of the Toner Cartridge by using one of the methods listed below: • Print a Supplies Information Report. [GP 2] • Open Easy Printer Manager, select [Machine Status] • Open the CWIS application. Select; [Status, Supplies, Black Imaging Unit]. 2. Check the remaining life of the Imaging Unit. 3. If the Imaging Unit has reached end of life, switch Off the power and replace the Imaging Unit.