Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5020DN — Trang 5/10

Code: E1-6

Description: Regi SNR Static JAM. IOT Registration Sensor ON is detected during standby.
Remedy: I/O Diagnostic Codes [08-05] IOT Registration Sensor
Check Items: • Sensor dirty • Foreign matter, burrs, or paper in the paper path • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the IOT Registration Sensor (PL 2.9). – Wire between Tray 1 Feed Sensor J156-3 ( P/J156) and LVPS J503-1 ( P/J503) – Wire between Tray 1 Feed Sensor J156-2 and LVPS J503-2 – Wire between Tray 1 Feed Sensor J156-1 and LVPS J503-3 • Replace the AIOC PWB (PL 8.1) .

Code: E3-1

Description: Exit SNR off JAM. Timeout between Fuser Exit Sensor ON and Fuser Exit Sensor OFF.
Remedy: I/O Diagnostic Codes [10-23] Fuser Exit Sensor
Check Items: • Fuser Exit Sensor dirty and Sensor Actuator deformed or damaged • Paper damaged or not within specification • Foreign matter, burrs, or paper in the paper path • Drive gear worn or damaged • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Fuser Exit Sensor (PL 6.2). – Wire between Fuser Exit Sensor J153-3 ( P/J153) and LVPS J505-1 ( P/J505) – Wire between Fuser Exit Sensor J153-2 and LVPS J505-2 – Wire between Fuser Exit Sensor J153-1 and LVPS J505-3 • Replace the LVPS (PL 8.1) and the AIOC PWB (PL 8.1) in that order.

Code: E3-6

Description: Exit SNR JAM. Fuser Exit Sensor ON is detected during standby.
Remedy: I/O Diagnostic Codes [10-23] Fuser Exit Sensor
Check Items: • Fuser Exit Sensor dirty and Sensor Actuator deformed or damaged • Foreign matter, burrs, or paper in the paper path • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Fuser Exit Sensor (PL 6.2). – Wire between Fuser Exit Sensor J153-3 ( P/J153) and LVPS J505-1 ( P/J505) – Wire between Fuser Exit Sensor J153-2 and LVPS J505-2 – Wire between Fuser Exit Sensor J153-1 and LVPS J505-3 • Replace the AIOC PWB (PL 8.1) .

Code: E5-1

Description: IOT L/H Cover open. The Left Hand Cover is open.
Remedy: I/O Diagnostic Codes [01-01] LH Cover Interlock Switch
Check Items: • Check that the Left Hand Cover closes correctly. • Check that the LH Cover Interlock Switch is correctly installed and that the electrical connection is good. • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the LH Cover Interlock Switch (PL 8.2). – Wire between LH Cover Interlock Switch FS151 ( FS151) and LVPS J506-4 ( P/J506) – Wire between LH Cover Interlock Switch FS152 ( FS152) and LVPS J506-3 • Replace the LVPS (PL 8.1) and the AIOC PWB (PL 8.1) in that order.

Code: E5-2

Description: IOT Front Cover open. The Front Cover is open.
Remedy: I/O Diagnostic Codes [01-12] Front Cover Interlock Switch
Check Items: • Check that the Front Cover closes correctly. • Check that the Front Cover Interlock Switch is correctly installed and that the electrical connection is good. • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Front Cover Interlock Switch (PL 8.2). – Wire between Front Cover Interlock Switch FS153 ( FS153) and LVPS J506-2 ( P/J506) – Wire between Front Cover Interlock Switch FS154 ( FS154) and LVPS J506-1 • Replace the LVPS (PL 8.1) and the AIOC PWB (PL 8.1) in that order.

Code: E6-1

Description: L/H Low Cover open. Access Cover 1 is open.
Remedy: I/O Diagnostic Codes [01-11] Tray1 Interlock Switch
Check Items: • Check that Access Cover 1 closes correctly. • Check that the Tray 1 Interlock Switch is correctly installed and that the electrical connection is good. • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 Interlock Switch (PL 2.5). – Wire between Tray 1 Interlock Switch J161-2 ( P/J161) and LVPS J501-9 ( P/J501) – Wire between Tray 1 Interlock Switch J161-1 and LVPS J501-10 • Replace the LVPS (PL 8.1) and the AIOC PWB (PL 8.1) in that order.

Code: E6-2

Description: STM L/H Cover open. Access Cover 2 is open.
Remedy: I/O Diagnostic Codes [01-10] STM Interlock Switch
Check Items: • Check that Access Cover 2 closes correctly. • Check that the STM Interlock Switch is correctly installed and that the electrical connection is good. • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM Interlock Switch (PL 11.5). – Wire between STM Interlock Switch J173-2 ( P/J173) and STM PWB J542-9 ( P/J542) – Wire between STM Interlock Switch J173-1 and STM PWB J542-10 • Replace the STM PWB (PL 11.5) , the LVPS (PL 8.1) , and the AIOC PWB (PL 8.1) in that order.

Code: E8-1

Description: Nup NG Out Of Range. The magnification is not within the range of 50 to 200% during Nup.
Remedy: • Press the [Stop] button on the Control Panel. • Press the [Paper Supply] button on the Control Panel. • Press the [Special Copy] button on the Control Panel. • Press the [Original Size Input] button on the Control Panel. • Press the [Clear All] button on the Control Panel.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie