Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5020DN — Trang 4/10

Code: C6-1

Description: Tray2 Paper Size Mismatch. • Paper that is different from the one in the Tray Settings is detected when feeding. • Or, paper size setting in the STM is different from the paper size specification of the job when STM is selected during a print job.
Remedy: • Press the [Stop] button on the Control Panel. • Change the paper size of STM to the one specified by the job.

Code: C7-1

Description: MSI Paper Size Mismatch. • Paper that is different from the one in the Tray Settings is detected when feeding. • Or, paper size setting in the MSI is different from the paper size specification of the job when MSI is selected during a print job.
Remedy: • Press the [Stop] button on the Control Panel. • Change the paper size of Bypass to the one specified by the job.

Code: C8-1

Description: F/O#1 SNR Static JAM. Tray1 Feed Sensor ON is detected during standby.
Remedy: I/O Diagnostic Codes [08-07] Tray1 Feed Sensor
Check Items: • Tray1 Feed Sensor dirty and Sensor Actuator deformed or damaged • Foreign matter, burrs, or paper in the paper path • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Tray 1 Feed Sensor (PL 2.5) . – Wire between Tray 1 Feed Sensor J158-3 ( P/J158) and STM PWB J501-6 ( P/J501) – Wire between Tray 1 Feed Sensor J158-2 and STM PWB J501-7 – Wire between Tray 1 Feed Sensor J158-1 and STM PWB J501-8 • Replace the AIOC PWB (PL 8.1) .

Code: C8-2

Description: F/O#2 SNR Static JAM. STM Feed Sensor ON is detected during standby.
Remedy: I/O Diagnostic Codes [08-06] STM Feed Sensor
Check Items: • STM Feed Sensor dirty and Sensor Actuator deformed or damaged • Foreign matter, burrs, or paper in the paper path • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the STM Feed Sensor (PL 11.5) . – Wire between STM Feed Sensor J172-3 ( P/J172) and STM PWB J542-6 ( P/J542) – Wire between STM Feed Sensor J172-2 and STM PWB J542-7 – Wire between STM Feed Sensor J172-1 and STM PWB J542-8 • Replace the STM PWB (PL 11.5) and the AIOC PWB (PL 8.1) in that order.

Code: C9-3

Description: MSI Regi SNR on JAM. Timeout between Bypass Solenoid ON and IOT Registration Sensor ON.
Remedy: I/O Diagnostic Codes • [08-05] IOT Registration Sensor • [08-17] Bypass Solenoid
Check Items: • Bypass Feed Roll, Retard Pad, or Bypass Take Away Roll dirty, contaminated with paper dust, worn, or faulty • IOT Registration Sensor dirty and Sensor Actuator deformed or damaged • Paper damaged, not within specification, or not loaded correctly • Foreign matter, burrs, or paper in the paper path • Drive gear worn or damaged • Bypass Solenoid faulty • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the IOT Registration Sensor (PL 2.9). – Wire between Tray 1 Feed Sensor J156-3 ( P/J156) and LVPS J503-1 ( P/J503) – Wire between Tray 1 Feed Sensor J156-2 and LVPS J503-2 – Wire between Tray 1 Feed Sensor J156-1 and LVPS J503-3 • Check that the Bypass Solenoid and the LVPS J502-1/3 ( P/J502) pins are connected securely with good electrical contact. If there is no problem, replace the Bypass Solenoid (PL 7.5). • Replace the AIOC PWB (PL 8.1) .

Code: E0-1

Description: CPM Image Lost. During a copy job in CMP Priority Mode, it is detected that the paper containing an image cannot be output after the image is deleted.
Remedy: Press the [Stop] button on the Control Panel.

Code: E0-1

Description: CPM Image Lost. During a copy job in CPM Priority Mode, the paper containing an image cannot be output after the image is deleted.
Remedy: Press the [Stop] button on the Control Panel.

Code: E1-2

Description: Exit SNR on JAM. Timeout between IOT Registration Clutch ON and Fuser Exit Sensor ON.
Remedy: I/O Diagnostic Codes • [08-10] IOT Registration Clutch • [10-23] Fuser Exit Sensor
Check Items: • Registration Roll dirty, contaminated with paper dust, worn, or faulty • Fuser Exit Sensor dirty and Sensor Actuator deformed or damaged • Paper damaged or not within specification • Foreign matter, burrs, or paper in the paper path • Drive gear worn or damaged • IOT Registration Clutch faulty • Check that the IOT Registration Clutch and the LVPS J503-4/5 ( P/J503) pins are connected securely with good electrical contact. If there is no problem, replace the IOT Registration Clutch (PL 2.9). • Check that the following wires are connected securely with good electrical contact. If there is no problem, replace the Fuser Exit Sensor (PL 6.2). – Wire between Fuser Exit Sensor J153-3 ( P/J153) and LVPS J505-1 ( P/J505) – Wire between Fuser Exit Sensor J153-2 and LVPS J505-2 – Wire between Fuser Exit Sensor J153-1 and LVPS J505-3 • Replace the AIOC PWB (PL 8.1) .
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie