Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5335 — Trang 28/33

Code: 077-305

Description: Tray Module L/H Cover Open RAP The Tray Module L/H Cover is open.
Remedy: 1. Turn the power OFF and ON. 2. Check the following: • The Tray Module L/H Cover for damage or mismatch • The Tray Module L/H Cover Switch for failure: Component Control [077-306] (PL 11.13) • The connection between the Tray Module L/H Cover Switch P/J104 and the Tray Module PWB P/J548 for open circuit, short circuit, and poor contact If no problems are found, replace the following parts in sequence: – Reload the machine software (GP 16). – Tray Module PWB (PL 11.13) – MCU PWB (PL 18.2)

Code: 077-307

Description: Duplex Cover Open RAP
Remedy: Check the following: • The Duplex Cover for damage or mismatch. • The Duplex Cover Switch for failure: Component Control [077-305] (PL 14.4) • The connection between the Duplex Cover Switch P/J108 and the MCU PWB P/J409 for open circuit, short circuit, and poor contact Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).

Code: 077-308

Description: L/H Upper Cover Open RAP
Remedy: Check the following: • The L/H High Cover Assembly for damage or mismatch • The L/H High Cover Switch for failure: Component Control [077-302] (PL 17.4) • Turn the power OFF. Check the connection between the L/H High Cover Switch P/J116 and the MCU PWB P/J409 for open circuit, short circuit, and poor contact Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).

Code: 077-309

Description: L/H Lower Cover Open RAP
Remedy: Check the following: • The L/H Lower Cover Assembly for damage or mismatch • The L/H Lower Cover Switch for failure: Component Control [077-301] (PL 15.2) • The connection between the L/H Lower Cover Switch P/J111 and the MCU PWB P/J410 for open circuit, short circuit, and poor contact Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).

Code: 077-314

Description: P/H Module Logic Fail RAP A fatal error was detected in the Tray Module.
Remedy: 1. Turn the power OFF and ON. 2. Turn the power OFF and check the connection between the MCU PWB P423 and the Tray Module PWB P/J541 for open circuit, short circuit, and poor contact. If no problems are found, replace the following parts in sequence: • Reload the machine software (GP 16). • Tray Module PWB (PL 11.13) • MCU PWB (PL 18.2)

Code: 077-900

Description: Registration Sensor Static Jam RAP When the power was turned ON, the M/C was stopped (Cycle Down/ Shut Down), or when the interlocks were closed (all interlocks including options), the Registration Sensor detected paper.
Remedy: Check the following: • The Registration Sensor for remaining paper, contamination, Actuator return failure, or improper installation • The Registration Sensor for failure: Component Control [077-104] (PL 15.1) • The connection between the Registration Sensor P/J121 and the MCU PWB P/J415 for open circuit, short circuit, and poor contact Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).

Code: 077-901

Description: Exit Sensor 1 Static Jam RAP When the power was turned ON, the M/C was stopped (Cycle Down/ Shut Down), or when the interlocks were closed (all interlocks including options), the Fuser Exit Sensor detected paper.
Remedy: Check the following: • The Fuser Exit Sensor for remaining paper, contamination, Actuator return failure, or improper installation • The Fuser Exit Sensor for failure: Component Control [077-101] (PL 7.1) Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).

Code: 077-902

Description: Exit Sensor 2 Static Jam RAP When the power was turned ON, the M/C was stopped (Cycle Down/ Shut Down), or when the interlocks were closed (all interlocks including options), the Exit 2 Sensor detected paper.
Remedy: Check the following: • The Exit 2 Sensor for remaining paper, contamination, Actuator return failure, or improper installation • The Exit 2 Sensor for failure: Component Control [077-100] (PL 17.4) • The connection between the Exit 2 Sensor P/J115 and the MCU PWB P/J411 for open circuit, short circuit, and poor contact • The L/H Upper Cover Assembly for damage or mismatch Reload the machine software (GP 16). If no problems are found, replace the MCU PWB (PL 18.2).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie