Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5645 — Trang 9/30

Code: 08-115, 08-117

Description: Tray 5 Misfeed RAP 08-115 The lead edge of the paper was late to the wait point sensor. 08-117 The lead edge of the paper failed to reach the feed sensor within the correct time after paper feed.
Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 32-55 ppm, go to 08-115A, 08-117A Tray 5 Misfeed RAP (32-55 ppm) • If the speed of the machine is 65-87 ppm, go to 08-115B, 08-117B Tray 5 Misfeed RAP (65-87 ppm).

Code: 08-115A, 08-117A

Description: Tray 5 Misfeed RAP (32-55 ppm) 08-115 The lead edge of the paper was late to the wait point sensor. 08-117 The lead edge of the paper failed to reach the feed sensor within the correct time after paper feed.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-105 tray 5 feed sensor, Q08-105. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-105. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed sensor, PL 8.45 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 08-117 tray 5 feed motor, MOT08-117. Open the door. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT08-117. Refer to: • GP 10 How to Check a motor. • P/J511, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed motor, PL 8.40 Item 3. • Tray 5 control PWB, PL 7.68 Item 8. The feed shaft rotates. Y↓N→Check the drive gears between the motor and the feed shaft. Install new components as necessary: • Motor drive gear, PL 8.40 Item 5. • Gear, PL 8.45 Item 18. The feed roll rotates Y↓N→Check the coupling between the feed roll and the clutch. Install new components as necessary: • One way gear, PL 8.45 Item 4. • Clutch, PL 8.45 Item 17. • Feed roll, PL 8.45 Item 2. The nudger roll rotates Y↓N→Check the coupling between the nudger roll and the one way coupling. Check the drive belt between the feed roll and the nudger roll. Install new components as necessary: • One way coupling, PL 8.45 Item 3. • Drive belt, PL 8.40 Item 7. • Nudger roll, PL 8.45 Item 2. The retard roll rotates Y↓N→Check the coupling between the retard roll and the retard clutch. Install new components as necessary: • Retard clutch, PL 8.45 Item 12. • Idler roll, PL 8.45 Item 16. • Retard roll, PL 8.45 Item 2. Enter dC330 code 08-046 tray 5 transport motor, MOT08-046. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-046. Refer to: • GP 10 How to Check a Motor. • P/J503, Tray 5 control PWB • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 transport motor, PL 8.40 Item 2. • Tray 5 control PWB, PL 7.68 Item 8. The transport rolls rotate. Y↓N→Check the drive belt and the one way pulley clutch for damage, GP 7. Check the belt tensioner. Install new components as necessary: • Drive belt, PL 8.40 Item 7. • One way pulley clutch, PL 8.45 Item 13. • Take away roller, PL 8.45 Item 14. Enter dC330 code 08-110 T5 wait point sensor, Q08-110. Press Start. NOTE: For trays 1 to 5 the input code 08-100 wait sensor is used to check the operation of the wait sensor. In addition tray 5 uses the input code 08-110 T5 wait point sensor, to check the paper present signal from the IOT PWB to the tray 5 control PWB. Open the left hand door and manually actuate the wait sensor. The display changes. Y↓N→Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Go to Flag 5. Manually actuate the wait sensor. Check for a signal change on the IOT PWB at P/J12 pin 10 and on the tray 5 control PWB at P/J512 pin 5. Check the wiring between the IOT PWB and the tray 5 control PWB. Install new components as necessary: • Tray 5 control PWB, PL 7.68 Item 8. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the steps that follow: • Clean the feed roll using a cloth dampened with water. • Install a new feed, nudger and retard roll, PL 8.45 Item 2.

Code: 08-115B, 08-117B

Description: Tray 5 Misfeed RAP (65-87 ppm) 08-115 The lead edge of the paper was late to the wait point sensor. 08-117 The lead edge of the paper failed to reach the feed sensor within the correct time after paper feed.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-105 tray 5 feed sensor, Q08-105. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-105. Refer to: • GP 11 How to Check a Sensor. • P/J505, Tray 5 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed sensor, PL 8.45 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. Enter dC330 code 08-117 tray 5 feed motor, MOT08-117. Open the door. Press Start. The motor runs. Y↓N→Go to Flag 4. Check MOT08-117. Refer to: • GP 10 How to Check a motor. • P/J511, Tray 5 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 feed motor, PL 8.40 Item 3. • Tray 5 control PWB, PL 7.68 Item 8. The feed shaft rotates. Y↓N→Check the drive gears between the motor and the feed shaft. Install new components as necessary: • Motor drive gear, PL 8.40 Item 5. • Gear, PL 8.45 Item 18. The feed roll rotates Y↓N→Check the coupling between the feed roll and the clutch. Install new components as necessary: • One way gear, PL 8.45 Item 4. • Clutch, PL 8.45 Item 17. • Feed roll, PL 8.45 Item 2. The nudger roll rotates Y↓N→Check the coupling between the nudger roll and the one way coupling. Check the drive belt between the feed roll and the nudger roll. Install new components as necessary: • One way coupling, PL 8.45 Item 3. • Drive belt, PL 8.40 Item 7. • Nudger roll, PL 8.45 Item 2. The retard roll rotates Y↓N→Check the coupling between the retard roll and the retard clutch. Install new components as necessary: • Retard clutch, PL 8.45 Item 12. • Idler roll, PL 8.45 Item 16. • Retard roll, PL 8.45 Item 2. Enter dC330 code 08-046 tray 5 transport motor, MOT08-046. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT08-046. Refer to: • GP 10 How to Check a Motor. • P/J503, Tray 5 control PWB • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 transport motor, PL 8.40 Item 2. • Tray 5 control PWB, PL 7.68 Item 8. The transport rolls rotate. Y↓N→Check the drive belt and the one way pulley clutch for damage, GP 7. Check the belt tensioner. Install new components as necessary: • Drive belt, PL 8.40 Item 7. • One way pulley clutch, PL 8.45 Item 13. • Take away roller, PL 8.45 Item 14. Enter dC330 code 08-110 T5 wait point sensor, Q08-110. Press Start. NOTE: For trays 1 to 5 the input code 08-100 wait sensor is used to check the operation of the wait sensor. In addition tray 5 uses the input code 08-110 T5 wait point sensor, to check the paper present signal from the IOT PWB to the tray 5 control PWB. Open the left hand door and manually actuate the wait sensor. The display changes. Y↓N→Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, PL 7.30 Item 24. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Go to Flag 5. Manually actuate the wait sensor. Check for a signal change on the IOT PWB at P/J12 pin 10 and on the Tray 5 control PWB at P/J512 pin 5. Check the wiring between the IOT PWB and the tray 5 control PWB. Install new components as necessary: • Tray 5 control PWB, PL 7.68 Item 8. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the steps that follow: • Clean the feed roll using a cloth dampened with water. • Install a new feed, nudger and retard roll, PL 8.45 Item 2.

Code: 08-150, 08-151

Description: Registration Jam Entry RAP 08-150 The lead edge of the paper failed to actuate the registration sensor within the correct time after the paper was released from the wait point. 08-151 The trail edge of the paper was late to the registration sensor after the registration clutch, CL08-070 on.
Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 32-55 ppm, go to 08-150A, 08-151A Registration Jam RAP (32-55 ppm) • If the speed of the machine is 65 - 87 ppm, go to 08-150B, 08-151B Registration Jam RAP (65-87 ppm).

Code: 08-150A, 08-151A

Description: Registration Jam RAP (32-55 ppm) 08-150 The lead edge of the paper failed to actuate the registration sensor within the correct time after the paper was released from the wait point. 08-151 The trail edge of the paper was late to the registration sensor after the registration clutch, CL08-070 on.
Remedy: NOTE: Ensure that the front door interlock is cheated when checking +24V components. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start. Open the left hand door and manually actuate the registration sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-150. Refer to: • GP 11 How to check a Sensor. • P/J16, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, (32-55 ppm) PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Open the left hand door and manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, (32-55 ppm) PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor. Press Start. The motor runs. Y↓N→Go to the 04A Main Drive Motor and Photoreceptor Motor RAP. While the motor is running, add code 08-070 registration clutch, CL08-070. Press Start. NOTE: The registration clutch will switch off after 5 seconds. Switch the registration clutch on / off up to 10 times. The jam clearance knob 4c, PL 8.15 Item 10, rotates when the registration clutch is energized. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration clutch, (32-55 ppm) PL 8.15 Item 7. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the following: • Check the registration transport rolls and registration rolls, (32-55 ppm) PL 8.15 Item 1, GP 7. • Check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure. If necessary, install a new registration clutch, PL 8.15 Item 7. • Check the tray 1 and 2 transport motor, PL 8.25 Item 5. Ensure that the motor runs correctly. • Check the tray 1 and 2 transport roll assemblies, transport drive belt and pulleys, PL 8.25 Item 2, PL 8.25 Item 3, GP 7. Install new components as necessary. • Install a new tray 1 and 2 control PWB, PL 7.10 Item 2.

Code: 08-150B, 08-151B

Description: Registration Jam RAP (65-87 ppm) 08-150 The lead edge of the paper failed to actuate the registration sensor within the correct time after the paper was released from the wait point. 08-151 The trail edge of the paper was late to the registration sensor after the registration clutch, CL08-070 on
Remedy: NOTE: Ensure that the front door interlock is cheated when checking +24V components. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start.. Open the left hand door and activate the registration sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-150. Refer to: • GP 11 How to check a Sensor. • P/J16, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, (65-87 ppm) PL 8.17 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Open the left hand door and activate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, PL 7.30 Item 25. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor. Press Start. The motor runs. Y↓N→Go to the 04A Main Drive Motor and Photoreceptor Motor RAP. While the motor is running, add code 08-070 registration clutch, CL08-070. Press Start. NOTE: The registration clutch will switch off after 5 seconds. Switch the registration clutch on / off up to 10 times. The jam clearance knob 4c, PL 8.17 Item 10, rotates when the registration clutch is energized. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration clutch, (65-87 ppm) PL 8.17 Item 7. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the following: • Check the registration transport rolls and registration rolls, (65-87 ppm) PL 8.17 Item 1, GP 7. • Check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure. If necessary, install a new registration clutch, PL 8.17 Item 7. • Check the tray 1 and 2 transport motor, PL 8.25 Item 5. Ensure that the motor runs correctly. • Check the tray 1 and 2 transport roll assemblies, transport drive belt and pulleys, PL 8.26 Item 1, GP 7. Install new components as necessary. • Install a new tray 1 and 2 control PWB, PL 7.10 Item 2.

Code: 08-155, 08-156

Description: Bypass Tray Registration Jam Entry RAP 08-155 The lead edge of the paper failed to actuate the registration sensor within the correct time after start of feed from the bypass tray. 08-156 The IOT detects that a sheet fed from the bypass has arrived to early at the registration sensor.
Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 32-55 ppm, go to 08-155A, 08-156A Bypass Tray Registration Jam RAP (32-55 ppm) • If the speed of the machine is 65-87 ppm, go to 08-155B, 08-156B Bypass Tray Registration Jam RAP (65-87 ppm).

Code: 08-155A, 08-156A

Description: Bypass Tray Registration Jam RAP (32- 55 ppm) 08-155 The lead edge of the paper failed to actuate the registration sensor within the correct time after start of feed from the bypass tray. 08-156 The IOT detects that a sheet fed from the bypass has arrived to early at the registration sensor.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start.. Manually actuate the registration sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-150. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor, code 08-070 registration clutch, CL08-070. Press Start. The jam clearance knob, 4c, PL 8.15 Item 10, rotates. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17 LVPS. • Fuse, PL 1.10 Item 9, GP 7. Enter dC330 code 08-050 feed solenoid, SOL08-050. Press Start. The solenoid energizes. Y↓N→Go to Flag 2. Check SOL08-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. •. • P/J10, IOT PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Feed solenoid, PL 7.30 Item 4. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the following: • Check the registration transport rolls and registration nip rolls, PL 8.15 Item 1. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure. • Check the idler roll and upper guide on the feed head. • Clean the feed roll and retard pad using a cloth dampened with water. • If necessary install a new feed and retard pad, PL 7.30 Item 21.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie