Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5645 — Trang 6/30

Code: 06-340

Description: ROS Laser Failure RAP 06-340. The IOT PWB has not detected the ROS laser reaching the operating speed.
Remedy: Go to Flag 3, connect a service meter to P/J 2 pin 7 and make a set of 5 copies. 0V is measured at P/J2 pin 7 on the IOT PWB during run. Y↓N→The xerographic module is fully home and the front door is fully closed or the front door interlock is cheated. Y↓N→Correct the condition. Go to Flag 1. Disconnect P/J18 from the LVPS. Check the following voltages on the LVPS: • +24V between pins 1 and 2. • +3.3V between pins 3 and 4. The voltages are good. Y↓N→Go to the relevant RAP: • 01B 0V Distribution RAP, refer to the 3.3V return and 24V return. • 01D +3.3V Distribution RAP. • 01G +24V Distribution RAP. Enter the dC330 output code 06-020. Go to Flag 2. The ROS motor gives a distinctive ascending frequency sound, of a short duration (5 to 6 seconds) during transition from standby to run. Y↓N→Go to the 06-020 ROS Motor Failure RAP. NOTE: The ROS must be removed from the machine, to disconnect P/J122 and P/J121. The ROS PWB where P/J122 and P/J121 are connected may not be marked with the correct PJ numbers. P/J122 can be identified as a four way power harness. P/J121 can be identified as a seven way signal harness. Check the wiring at Flag 1, Flag 2 and Flag 3. The wiring is good. Y↓N→Repair the wiring or install new harness PL 6.10 Item 5. Install a new ROS, PL 6.10 Item 4. Go to Flag 4. Check that P/J109 (32-55 ppm) or P/J228 (65-87 ppm) on the image processing PWB is securely connected. If the fault is still present, remove the ROS. Go to Flag 4 and ensure that PJ122 on the ROS is securely connected. If the fault is still present, go to Flag 4 and check the continuity of the ROS data cable ( P/J228 or P/J109 to PJ122). The ROS data cable is good Y↓N→Install a new ROS power distribution/communications harness, PL 6.10 Item 5. Install new parts in the following order: • ROS, PL 6.10 Item 4. • Image processing PWB (32-55 ppm), PL 3.20 Item 3. • Image processing PWB (65-87 ppm), PL 3.10 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2.

Code: 06-350

Description: ROS Laser Not Under Control RAP 06-350. The IOT monitor has not received a reset command from the IOT ROS controller for more than 5 seconds during print.
Remedy: Perform the 03-395, 396, 852, 853 IOT PWB Faults RAP.

Code: 07-301

Description: Tray 1 Open During Run RAP 07-301 Tray 1 was opened during run when the paper is fed from tray 1
Remedy: Enter dC330 code 07-301 tray 1 home switch, S07-301. Press Start. Open and fully close the tray. The display changes. Y↓N→Go to Flag 1. Check S07-301. Refer to: • GP 13 How to Check a Switch. • Tray 1 home (H) +5V. Check at the switch terminal on the PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 1 and 2 control PWB, PL 7.10 Item 2. Perform the following: • Check the paper size leaf spring are mounted correctly, PL 7.10 Item 3. • Check the actuator cam on the paper tray. • If the problem continues, install new Tray 1 and 2 control PWB, PL 7.10 Item 2.

Code: 07-302

Description: Tray 2 Open During Run RAP 07-302 Tray 2 was opened during run when the paper is fed from tray 2.
Remedy: Enter dC330 code 07-302 tray 2 home switch, S07-302. Press Start. Open and fully close the tray. The display changes. Y↓N→Go to Flag 1. Check S07-302. Refer to: • GP 13 How to Check a Switch. • Tray 1 home (H) +5V. Check at the switch terminal on the PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 1 and 2 control PWB, PL 7.10 Item 2. Perform the following: • Check the paper size leaf spring are mounted correctly, PL 7.10 Item 3. • Check the actuator on the paper tray. • If the problem continues, install new Tray 1 and 2 control PWB, PL 7.10 Item 2.

Code: 07-303

Description: Tray 3 Open During Run RAP 07-303 Tray 3 open during run when the paper is fed from tray 3.
Remedy: Enter dC330 code 07-303 tray 3 home switch, S07-303. Press Start. Open and fully close the tray. The display changes. Y↓N→Go to Flag 1. Check S07-303. Refer to: • GP 13 How to Check a Switch. • P/J392, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 3 home switch, PL 7.20 Item 4. • HCF control PWB, PL 7.20 Item 2. Check the switch holder, PL 7.20 Item 3. If the problem continues, install new components as necessary: • Tray 3 home switch, PL 7.20 Item 4. • HCF control PWB, PL 7.20 Item 2.

Code: 07-304

Description: Tray 4 Open During Run RAP 07-304 Tray 4 0pen during run when the paper is fed from tray 4.
Remedy: Enter dC330 code 07-304 tray 4 home switch, S07-304. Press Start. Open and fully close the tray. The display changes. Y↓N→Go to Flag 1. Check S07-304. Refer to: • GP 13 How to Check a Switch. • P/J392, HCF control PWB. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 4 home switch, PL 7.20 Item 4. • HCF control PWB, PL 7.20 Item 2. Check the switch holder, PL 7.20 Item 3. If the problem continues, install new components as necessary: • Tray 4 home switch, PL 7.20 Item 4. • HCF control PWB, PL 7.20 Item 2.

Code: 07-306

Description: Tray 5 Door Open During Run RAP 07-306 Tray 5 door open during run when the paper is fed from tray 5.
Remedy: Enter dC330 code 07-306 tray 5 door switch, S07-306 Press Start. Open and fully close the door The display changes. Y↓N→Go to Flag 1. Check S07-306. Refer to: • GP 13 How to Check a Switch. • 01E +5V Distribution RAP • P/J507, Tray 5 control PWB. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 5 door switch, PL 7.60 Item 6. • Tray 5 control PWB, PL 7.68 Item 8. If the problem continues, install new components as necessary: • Tray 5 door switch, PL 7.60 Item 6 • Tray 5 control PWB, PL 7.68 Item 8.

Code: 07-353

Description: Tray 1 Elevator Lift Failure RAP 07-353 Tray 1 stack height sensor did not actuate within the correct time after the feed / elevator motor turned on.
Remedy: Enter dC330 code 07-336 tray 1 stack height sensor, Q07-336. Press Start. Pull out tray 1 and push fully home. The display changes Y↓N→Go to Flag 1. Check Q07-383. Refer to: • GP 11 How to Check a Sensor. • P/J274, Tray 1 and 2 control PWB • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Tray 1 stack height sensor, PL 8.26 Item 7. • Tray 1 and 2 control PWB, PL 7.10 Item 2. CAUTION To prevent damage to the elevator and paper feed mechanism, the paper tray must be pulled out before MOT07-010 is run in diagnostics. Enter dC330 code 07-010 tray 1 feed / elevator motor, MOT07-010. Pull out tray 1. Press Start. The motor runs Y↓N→Go to Flag 2. Check MOT07-010. Refer to: • GP 10 How to Check a Motor. • P/J274, Tray 1 and 2 control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP Install new components as necessary: • Tray 1 Feed / elevator motor, PL 8.26 Item 8. • Tray 1 and 2 control PWB, PL 7.10 Item 2. Perform the following: • Check the feeder / elevator motor drive gears. • Check the tray 1 stack height mechanism on the feeder assembly, If the fault still occurs then go to 07A Tray 1 and Tray 2 False Paper Level RAP.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie