• Code: 08-155B, 08-156B
• Description: Bypass Tray Registration Jam RAP (65- 87 ppm) 08-155 The lead edge of the paper failed to actuate the registration sensor within the correct time after start of feed from the bypass tray. 08-156 The IOT detects that a sheet fed from the bypass has arrived to early at the registration sensor.
• Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start.. Activate the registration sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-150. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, (65-87 ppm) PL 8.17 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor, code 08-070 registration clutch, CL08-070. Press Start. The jam clearance knob, 4c, PL 8.17 Item 10, rotates. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17 LVPS. • Fuse, PL 1.10 Item 9, GP 7. Enter dC330 code 08-050 feed solenoid, SOL08-050. Press Start. The solenoid energizes. Y↓N→Go to Flag 2. Check SOL08-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. •. • P/J10, IOT PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Feed solenoid, PL 7.30 Item 4. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the following: • Check the registration transport rolls and registration nip rolls, PL 8.17 Item 1. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure. • Check the idler roll and upper guide on the feed head. • Clean the feed roll and retard pad using a cloth dampened with water. • If necessary install a new feed and retard pad, PL 7.30 Item 21.

• Code: 08-160, 08-161
• Description: Duplex Paper Path Jam Entry RAP 08-160 The lead edge of the first sheet of a job fed into the duplex path failed to actuate the Duplex sensor in the correct time. 08-161 The trail edge is late to the duplex sensor after of the first sheet of a job fed into the duplex path failed to actuate the duplex sensor in the correct time.
• Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 32-55 ppm, go to 08-160A, 08-161A Duplex Paper Path Jam RAP (32-55 ppm) • If the speed of the machine is 65-87 ppm, go to 08-160B, 08-161B Duplex paper path Jam RAP (65-87 ppm).

• Code: 08-160A, 08-161A
• Description: Duplex Paper Path Jam RAP (32-55 ppm) 08-160 The lead edge of the first sheet of a job fed into the duplex path failed to actuate the Duplex sensor in the correct time. 08-161 The trail edge is late to the duplex sensor after of the first sheet of a job fed into the duplex path failed to actuate the duplex sensor in the correct time.
• Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-160 duplex sensor, Q08-160. Press Start. Manually actuate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-160. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Duplex sensor, (32-55 ppm) PL 8.22 Item 4. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-060 duplex motor, MOT08-060. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-060. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB. • P/J50, P/J91, duplex motor driver PWB. • 01G +24V Distribution RAP. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Duplex motor, (32-55 ppm) PL 8.22 Item 8. • Duplex motor driver PWB, (32-55 ppm) PL 8.22 Item 9. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. The transport rolls rotate. Y↓N→Check the drive belt and pulleys, (32-55 ppm) PL 8.22 Item 2, PL 8.22 Item 10. Enter dC330 code 10-030 Inverter Motor, 10-030. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT10-030. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB. • P/J45, P/J55. • 01G +24V Distribution RAP. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter motor, PL 10.11 Item 11. • Inverter motor driver PWB, PL 10.11 Item 22. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. The transport rolls rotate. Y↓N→Check drive gears, GP 7, PL 10.15. Enter dC330 code 10-050 inverter nip solenoid, SOL10-050. Press Start. The solenoid energizes. Y↓N→Go to Flag 4. Check SOL10-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter Nip Solenoid, PL 10.11 Item 6. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-045 inverter path solenoid, SOL10 045. Press Start. The solenoid energizes. Y↓N→Go to Flag 5. Check SOL10-045. Refer to: • GP 12 How to check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter path solenoid, PL 10.11 Item 14. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Check the following, refer to GP 7: • Duplex nip rolls, (32-55 ppm) PL 8.22 Item 7. • Nip split shaft assembly, PL 10.11 Item 4. • Idler rolls, PL 10.12 Item 15. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure.

• Code: 08-160B, 08-161B
• Description: Duplex Paper Path Jam RAP (65-87 ppm) 08-160 The lead edge of the first sheet of a job fed into the duplex path failed to actuate the Duplex sensor in the correct time. 08-161 The trail edge is late to the duplex sensor after of the first sheet of a job fed into the duplex path failed to actuate the duplex sensor in the correct time.
• Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-160 duplex sensor, Q08-160. Press Start. Activate the sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-160. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Duplex sensor, (65-87 ppm) PL 8.20 Item 4. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-060 duplex motor, MOT08-060. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-060. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB. • P/J50, P/J91, duplex motor driver PWB. • 01G +24V Distribution RAP. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Duplex motor, (65-87 ppm) PL 8.20 Item 8. • Duplex motor driver PWB, (65-87 ppm) PL 8.20 Item 9. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. The transport rolls rotate. Y↓N→Check the drive belt and pulleys, (65-87 ppm) PL 8.20 Item 2, PL 8.20 Item 10. Enter dC330 code 10-030 Inverter Motor, 10-030. Press Start. The motor runs. Y↓N→Go to Flag 3. Check MOT10-030. Refer to: • GP 10 How to Check a Motor. • P/J4, IOT PWB. • P/J45, P/J55. • 01G +24V Distribution RAP. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter motor, PL 10.11 Item 11. • Inverter motor driver PWB, PL 10.11 Item 22. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. The transport rolls rotate. Y↓N→Check drive gears, GP 7, PL 10.15. Enter dC330 code 10-050 inverter nip solenoid, SOL10-050. Press Start. The solenoid energizes. Y↓N→Go to Flag 4. Check SOL10-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter Nip Solenoid, PL 10.11 Item 6. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 10-045 inverter path solenoid, SOL10 045. Press Start. The solenoid energizes. Y↓N→Go to Flag 5. Check SOL10-045. Refer to: • GP 12 How to check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Inverter path solenoid, PL 10.11 Item 14. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Check the following, refer to GP 7: • Duplex nip rolls, (65-87 ppm) PL 8.20 Item 7. • Nip split shaft assembly, PL 10.11 Item 4. • Idler rolls, PL 10.12 Item 15. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure.

• Code: 08-171
• Description: Unexpected Time Out RAP 08-171 The IOT detects an unexpected event for a known sheet. A sheet left in the machine after jam clearance.
• Remedy: • Enter the machine status mode and check for the active messages. Refer to OF4 Status Codes and Message RAP for the jam clearance procedure. • Check the condition of the paper in all trays, Refer to IQ1 and GP 20. • Check for obstructions in the paper path. • Make sure that all covers and paper guides are closed, and latch correctly. • Check for paper in the output device
  If the initial actions did not resolve the problem. Switch off the machine, then switch on the machine, GP 14. If a fault code is displayed then go to the appropriate RAP.

• Code: 08-174
• Description: Missing Pre-release Sheet RAP 08-174 The IOT detected a missing pre-release sheet.
• Remedy: • Enter the machine status mode and check for the active messages. Refer to OF4 Status Codes and Message RAP for the jam clearance procedure. • Check the condition of the paper in all trays. Refer to IQ1 and GP 20. • Check for obstructions in the registration paper path. • Make sure that all covers and paper guides are closed, and latch correctly.
  If the initial actions did not resolve the problem. Switch off the machine, then switch on the machine, GP 14. If a fault code is displayed then go to the appropriate RAP.

• Code: 08-181
• Description: Unexpected Time Out in Simplex Inverted Mode RAP 08-181 The IOT detected an unexpected time out for a known simplex inverted sheet of paper.
• Remedy: • Enter the machine status mode and check for the active messages. Refer to OF4 Status Codes and Message RAP for the jam clearance procedure. • Check the condition of the paper in all trays. Refer to IQ1 and GP 20. • Check for obstructions in the simplex and inverted paper path. • Make sure that all covers and paper guides are closed, and latch correctly.
  If the initial actions did not correct the problem, perform the following: • Switch off the machine, then switch on the machine, GP 14. • If a fault code is displayed then go to the appropriate RAP. • Check the inverter gate is free to move and operates correctly, PL 10.12 Item 7.

• Code: 08-182
• Description: Unexpected Time Out in Duplex Mode RAP 08-182 The IOT detected an unexpected time out for a known duplex sheet of paper.
• Remedy: • Enter the machine status mode and check for the active messages. Refer to OF4 Status Codes and Message RAP for the jam clearance procedure. • Check the condition of the paper in all trays. Refer to IQ1 and GP 20. • Check for obstructions in the duplex paper path.
  If the initial actions did not resolve the problem. Switch off the machine, then switch on the machine, GP 14. If a fault code is displayed then go to the appropriate RAP.