Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre 5740 — Trang 11/27

Code: 08-133

Description: Tray 4 Paper Feed Jam RAP (W/TAG 151) 08-133 The lead edge of the paper was late to the HCF exit sensor when feeding from tray 4.
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-108 HCF exit sensor, Q08-104. Press Start. Manually actuate the HCF exit sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-108. Refer to: • GP 11 How to Check a Sensor. • P/J3, HCF control PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • HCF exit sensor, PL 8.33 Item 3. • HCF control PWB, PL 7.21 Item 2. Enter dC330 code 08-045 HCF transport motor, MOT08-045. Press Start. The motor runs. Y↓N→Go to Flag 2. Check MOT08-045. Refer to: • GP 10 How to Check a Motor. • P/J6, HCF control PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • HCF transport motor, PL 8.36 Item 13. • HCF control PWB, PL 7.21 Item 2. The transport rolls rotate. Y↓N→Check the tray 3 and 4 transport roll, PL 8.32 Item 4 Perform the 08-104, 08-114 Tray 4 Misfeed RAP.

Code: 08-150, 08-151

Description: Registration Jam Entry RAP 08-150 The lead edge of the paper failed to actuate the registration sensor within the correct time after the paper was released from the wait point. 08-151 The trail edge of the paper was late to the registration sensor after the registration clutch, CL08-070 on.
Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 35-55 ppm, go to 08-150A, 08-151A Registration Jam RAP (35-55 ppm) • If the speed of the machine is 65-90 ppm, go to 08-150B, 08-151B Registration Jam RAP (65-90 ppm).

Code: 08-150A, 08-151A

Description: Registration Jam RAP (35-55 ppm)
Remedy: NOTE: Ensure that the front door interlock is cheated when checking +24V components. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start. Open the left hand door and manually actuate the registration sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-150. Refer to: • GP 11 How to check a Sensor. • P/J16, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, (35-55 ppm) PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Open the left hand door and manually actuate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, (35-55 ppm) PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor. Press Start. The motor runs. Y↓N→Go to the 04A Main Drive Motor and Photoreceptor Motor RAP. While the motor is running, add code 08-070 registration clutch, CL08-070. Press Start. NOTE: The registration clutch will switch off after 5 seconds. Switch the registration clutch on / off up to 10 times. The jam clearance knob 4c, PL 8.15 Item 10, rotates when the registration clutch is energized. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration clutch, (35-55 ppm) PL 8.15 Item 7. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the following: • Check the registration transport rolls and registration rolls, (35-55 ppm) PL 8.15 Item 1, GP 7. • Check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure. If necessary, install a new registration clutch, PL 8.15 Item 7. • Check the tray 1 and 2 transport motor, PL 8.25 Item 5. Ensure that the motor runs correctly. • Check the tray 1 and 2 transport roll assemblies, transport drive belt and pulleys, PL 8.25 Item 2, PL 8.25 Item 3, GP 7. Install new components as necessary. • Install a new tray 1 and 2 control PWB, PL 7.10 Item 2. • Refer to. Make sure PJ44 is securely connected.

Code: 08-150B, 08-151B

Description: Registration Jam RAP (65-90 ppm)
Remedy: NOTE: Ensure that the front door interlock is cheated when checking +24V components. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start.. Open the left hand door and activate the registration sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-150. Refer to: • GP 11 How to check a Sensor. • P/J16, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, (65-90 ppm) PL 8.17 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 08-100 wait sensor, Q08-100. Press Start. Open the left hand door and activate the wait sensor. The display changes. Y↓N→Go to Flag 2. Check Q08-100. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Wait sensor, PL 7.30 Item 25. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor. Press Start. The motor runs. Y↓N→Go to the 04A Main Drive Motor and Photoreceptor Motor RAP. While the motor is running, add code 08-070 registration clutch, CL08-070. Press Start. NOTE: The registration clutch will switch off after 5 seconds. Switch the registration clutch on / off up to 10 times. The jam clearance knob 4c, PL 8.17 Item 10, rotates when the registration clutch is energized. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17, LVPS. • Fuse, PL 1.10 Item 9, GP 7. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration clutch, (65-90 ppm) PL 8.17 Item 7. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the following: • Check the registration transport rolls and registration rolls, (65-90 ppm) PL 8.17 Item 1, GP 7. • Check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure. If necessary, install a new registration clutch, PL 8.17 Item 7. • Check the tray 1 and 2 transport motor, PL 8.25 Item 5. Ensure that the motor runs correctly. • Check the tray 1 and 2 transport roll assemblies, transport drive belt and pulleys, PL 8.26 Item 1, GP 7. Install new components as necessary. • Install a new tray 1 and 2 control PWB, PL 7.10 Item 2. • Refer to. Make sure PJ44 is securely connected.

Code: 08-155, 08-156

Description: Bypass Tray Registration Jam Entry RAP 08-155 The lead edge of the paper failed to actuate the registration sensor within the correct time after start of feed from the bypass tray. 08-156 The IOT detects that a sheet fed from the bypass has arrived to early at the registration sensor.
Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 35-55 ppm, go to 08-155A, 08-156A Bypass Tray Registration Jam RAP (35-55 ppm) • If the speed of the machine is 65-90 ppm, go to 08-155B, 08-156B Bypass Tray Registration Jam RAP (65-90 ppm).

Code: 08-155A, 08-156A

Description: Bypass Tray Registration Jam RAP (35- 55 ppm)
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start.. Manually actuate the registration sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-150. Refer to: • GP 11 How to Check a Sensor. • P/J5, IOT PWB. • 01D +3.3V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, PL 8.15 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor, code 08-070 registration clutch, CL08-070. Press Start. The jam clearance knob, 4c, PL 8.15 Item 10, rotates. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17 LVPS. • Fuse, PL 1.10 Item 9, GP 7. Enter dC330 code 08-050 feed solenoid, SOL08-050. Press Start. The solenoid energizes. Y↓N→Go to Flag 2. Check SOL08-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. •. • P/J10, IOT PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Feed solenoid, PL 7.30 Item 4. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the following: • Check the registration transport rolls and registration nip rolls, PL 8.15 Item 1. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure. • Check the idler roll and upper guide on the feed head. • Clean the feed roll and retard pad using a cloth dampened with water. • If necessary install a new feed and retard pad, PL 7.30 Item 21.

Code: 08-155B, 08-156B

Description: Bypass Tray Registration Jam RAP (65- 90 ppm)
Remedy: NOTE: The front door interlock must be cheated when checking +24V components. Enter dC330 code 08-150 registration sensor, Q08-150. Press Start.. Activate the registration sensor. The display changes. Y↓N→Go to Flag 1. Check Q08-150. Refer to: • GP 11 How to Check a Sensor. • P/J16, IOT PWB. • 01E +5V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Registration sensor, (65-90 ppm) PL 8.17 Item 3. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Enter dC330 code 04-010 main drive motor, code 08-070 registration clutch, CL08-070. Press Start. The jam clearance knob, 4c, PL 8.17 Item 10, rotates. Y↓N→Go to Flag 3. Check CL08-070. Refer to: • GP 12 How to Check a Solenoid or Clutch. • P/J5, IOT PWB. • P/J17 LVPS. • Fuse, PL 1.10 Item 9, GP 7. Enter dC330 code 08-050 feed solenoid, SOL08-050. Press Start. The solenoid energizes. Y↓N→Go to Flag 2. Check SOL08-050. Refer to: • GP 12 How to Check a Solenoid or Clutch. •. • P/J10, IOT PWB. • 01G +24V Distribution RAP. • 01B 0V Distribution RAP. Install new components as necessary: • Feed solenoid, PL 7.30 Item 4. • Perform OF7 IOT PWB Diagnostics RAP before a new IOT PWB is installed, PL 1.10 Item 2. Perform the following: • Check the registration transport rolls and registration nip rolls, PL 8.17 Item 1. • If the fault still occurs, check the drives plate on the registration clutch for damage and contamination. Refer to the replacement procedure. • Check the idler roll and upper guide on the feed head. • Clean the feed roll and retard pad using a cloth dampened with water. • If necessary install a new feed and retard pad, PL 7.30 Item 21.

Code: 08-160, 08-161

Description: Duplex Paper Path Jam Entry RAP 08-160 The lead edge of the first sheet of a job fed into the duplex path failed to actuate the Duplex sensor in the correct time. 08-161 The trail edge is late to the duplex sensor after of the first sheet of a job fed into the duplex path failed to actuate the duplex sensor in the correct time.
Remedy: Identify the speed of the machine, refer to SCP 7 Machine features. Perform one of the steps that follow: • If the speed of the machine is 35-55 ppm, go to 08-160A, 08-161A Duplex Paper Path Jam RAP (35-55 ppm) • If the speed of the machine is 65-90 ppm, go to 08-160B, 08-161B Duplex paper path Jam RAP (65-90 ppm).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie