Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Xerox WorkCentre Pro 412

Code: 01

Description: White copy
Causes: • Check the scan-cover is not open. • Check shading profile. • Check white/black reference voltage in Main PBA. • Check the CCD lamp is on when scanning.
Remedy: • Ambient light can cause image problems • Remake shading profile in the Tech mode. • Replace Main PBA if it is defective. - U16-97 = 3.3V - U16-98 = 3.3V - U16-99 = 1.5V • If the CCD is defective, replace it. - CN3-19 is 5.8V when white original copying for R, B and 3.5V for G.

Code: 02

Description: Black copy
Causes: • Check for CCD problem in Main PBA. • Check shading profile. • Check the CCD problem in Main PBA
Remedy: • Check the CCD harness contacts. • Remake shading profile in the Tech mode. • If the CCD is defective, install a new ELEC/MECH-SCANNER MODULE, PL 2-2-21. - Cn3-19 is 7.3V when idle for R, B, and 5V for G.

Code: 03

Description: Defective image quality
Causes: • Check shading profile. • Check the gap between original and scanner glass. • Check printing quality.
Remedy: • Remake shading profile in the Tech mode. • A gap greater than 0.5mm can cause a blurred image. • See “Print” troubleshooting.

Code: 04

Description: Abnormal noise
Causes: • Check the scanner glass and any mechanical disturbance. • Check the motor driver in Driver PBA.
Remedy: • Check the scanner glass is correctly located and clean, check that the CCD carriage moves smoothly. • If any driver is defective, replace the main PBA. - U55 or U55-1, 15 = 0V to 24V swing signal when operating.

Code: 05

Description: Scanning error
Causes: • Check the printer cable. • Check how TWAIN driver is installed. • Check harness contact. • Check the IEEE1284 signal level.
Remedy: • Check correct installation, and use standard IEEE1284 cable. • Remove any other scanner driver. • Reboot after reinstallation of the TWAIN driver. • Check CN14 contact in Main PBAl. • If any signal level is defective, install a new Main PBA. - U36-66-74 in Main PBA = 0.8V to 2.4V TTL signal. • If necessary, install a new PBA MAIN MAIN, PL 1-19

Code: 06

Description: Defective image quality
Causes: • Check shading profile. • Check the gap between original and scanner glass.
Remedy: • Remake shading profile in the Tech mode. • A gap greater than 0.5mm can cause a blurred image.

Code: 07

Description: Abnormal noise
Causes: • Check the scanner glass and any mechanical disturbance. • Check the motor driver in Driver PBA.
Remedy: • Check the scanner glass is correctly located and clean, check that the CCD carriage moves smoothly. • If any driver is defective, replace the Main PBA. - U55 or U56-19 = 0V to 24V swing signal when operating.

Code: 08

Description: TEL LINE CANNOT BE ENGAGED (NO DIAL TONE)
Causes: • When you press the “OHD” key: a) Check line cord connection. b) Check MAIN LIU harness, and CN1(LIU PBA). c) Check relay operation of LIU PBA: Is the control signal of CN20-7(main) low?
Remedy: a) Insert plug into the socket named “line”. b) Replace defective parts. c) Replace main PBA IF the control signal of CN20-7(main) is high. Replace LIU PBA if high but phone line cannot be connected.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie