• Code: 604-1024-00
• Description: Faulty/insufficient image memory (Main Controller PCB1)
• Causes: No necessary memory at Main Controller PCB 1
• Remedy: Make the Memory capacity at Main Controller PCB 1 as indicated by 1024.

• Code: 604-1536-00
• Description: Faulty/insufficient image memory (Main Controller PCB1)
• Causes: No necessary memory at Main Controller PCB 1
• Remedy: Make the Memory capacity at Main Controller PCB 1 as indicated by 1536.

• Code: 613-0512-00
• Description: Faulty/insufficient image memory
• Causes: No necessary memory at Main Controller PCB
• Remedy: Make the Memory capacity at Main Controller PC as indicated by 0512.

• Code: 613-1024-00
• Description: Faulty/insufficient image memory
• Causes: No necessary memory at Main Controller PCB
• Remedy: Make the Memory capacity at Main Controller PCB as indicated by 1024.

• Code: 613-1536-00
• Description: Faulty/insufficient image memory
• Causes: No necessary memory at Main Controller PCB
• Remedy: Make the Memory capacity at Main Controller PCB as indicated by 1536.

• Code: 614-0001-00
• Description: Flash PCB error
• Causes: The Flash PCB could not be recognized, or the Flash PCB was not formatted.
• Remedy: [Related parts] R1.00 - SATA Flash PCB - Main Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the SATA Flash PCB again to check that it is properly installed. 2. Enter safe mode using (2+8) startup, and execute Flash Format using SST or a USB flash drive. 3. After replacing the SATA Flash PCB, reinstall the system software using SST or a USB flash drive. 4. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

• Code: 614-0002-00
• Description: Error in system on the Flash PCB
• Causes: The file system could not be initialized normally at startup. When this error occurs, the system has not been started normally. Therefore, it may not be recorded in the error log.
• Remedy: [Related parts] R1.00 - SATA Flash PCB - Main Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the SATA Flash PCB again to check that it is properly installed. 2. Enter safe mode using (2+8) startup, and execute Flash Format using SST or a USB flash drive. 3. After replacing the SATA Flash PCB, reinstall the system software using SST or a USB flash drive. 4. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.

• Code: 614-0006-00
• Description: Error in system on the Flash PCB
• Causes: Bootable was not found on the Flash PCB.
• Remedy: [Related parts] R1.00 - SATA Flash PCB - Main Controller PCB [Remedy] Perform the following in the order while checking whether the error is cleared. - Reinstall the necessary application software once the error is cleared. 1. After turning OFF the main power, remove and then install the SATA Flash PCB again to check that it is properly installed. 2. Enter safe mode using (2+8) startup, and execute Flash Format using SST or a USB flash drive. 3. After replacing the SATA Flash PCB, reinstall the system software using SST or a USB flash drive. 4. Replace the Main Controller PCB. [Reference] For backup and restoration, refer to "Adjustment> Main Controller System" and "Appendix> Backup Data List" in the Service Manual.