Causes: Software process error (for log collection)
Remedy: [Remedy] Collect debug log and contact the sales company. [Reference] By setting "COPIER (LEVEL2)> OPTION> FNC-SW> SELF-CHK" to "1", it is handled as an error.
Causes: The Reader Scanner Unit could not detect the home position when starting scanning operation.
Remedy: [Related parts] R1.00 - Harness between the Reader Controller PCB (UN1/J102) and the Scanner Unit HP Sensor (PS2/ J5202) - Harness between the Reader Controller PCB (UN1/J108) and the Scanner Motor (M1/J601) - Scanner Unit HP Sensor (PS2) - Scanner Motor (M1) - Reader Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
Causes: The Reader Scanner Unit could not detect the home position when completing scanning operation.
Remedy: [Related parts] R1.00 - Harness between the Reader Controller PCB (UN1/J102) and the Scanner Unit HP Sensor (PS2/ J5202) - Harness between the Reader Controller PCB (UN1/J108) and the Scanner Motor (M1/J601) - Scanner Unit HP Sensor (PS2) - Scanner Motor (M1) - Reader Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
Causes: An error in the Reader Scanner Unit position was detected when reading of a job was started.
Remedy: [Related parts] R1.00 - Harness between the Reader Controller PCB (UN1/J102) and the Scanner Unit HP Sensor (PS2/ J5202) - Harness between the Reader Controller PCB (UN1/J108) and the Scanner Motor (M1/J601) - Scanner Unit HP Sensor (PS2) - Scanner Motor (M1) - Reader Controller PCB (UN1) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. - Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP - Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES
Causes: The DADF Glass (for back side) could not detect the home position when starting scanning operation.
Remedy: [Related parts] R1.00 - Harness between the DADF Driver PCB (UN3/J413) and the Glass HP Sensor (SR18/J630) - Harness between the DADF Driver PCB (UN3/J415) and the Glass Shift Motor (M8/J1225) - Glass HP Sensor (SR18) - Glass Shift Motor (M8) - DADF Driver PCB (UN03) [Remedy] Check/replace the related harness/cable, connector and parts.
Causes: The DADF Glass (for back side) could not detect the home position when completing scanning operation.
Remedy: [Related parts] R1.00 - Harness between the DADF Driver PCB (UN3/J413) and the Glass HP Sensor (SR18/J630) - Harness between the DADF Driver PCB (UN3/J415) and the Glass Shift Motor (M8/J1225) - Glass HP Sensor (SR18) - Glass Shift Motor (M8) - DADF Driver PCB (UN03) [Remedy] Check/replace the related harness/cable, connector and parts.
Causes: The Reader Controller PCB did not detect 24 V when the main power was turned ON.
Remedy: [Related parts] R1.00 - Harness between the Reader Controller PCB (UN1/J111) and the DADF Driver PCB (UN03/J402) - Harness between the Reader Controller PCB (UN1/J101) and the Relay PCB (UN7/J1808) - Harness between the Relay PCB (UN7/J1802) and the DC Power Supply PCB (24VA) (UN34/ J202) - Harness between the Relay PCB (UN7/J1803) and the DC Power Supply PCB (24VB) (UN35/ J2020) - Harness between the DC Power Supply PCB (24VA/24VB) (UN34/J102 and UN35/J1020) and the AC Driver PCB (UN8/J810 and J813) - Harnesses between the DC Controller PCB (UN2/J1200 and J1224) and the Relay PCB (UN7/ J1817 and J1805) - Reader Controller PCB (UN1) - DADF Driver PCB (UN03) - Relay PCB (UN7) - DC Power Supply PCB (24VA) (UN34) - DC Power Supply PCB (24VB) (UN35) - AC Driver PCB (UN8) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When an error is detected, conduction of 24 V is stopped. At power check, check if 24 V is conducted or rated voltage is output by repeating power cycling of the machine. - Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Causes: The DADF Driver PCB did not detect 24 V when the main power was turned ON.
Remedy: [Related parts] R1.00 - Harness between the Reader Controller PCB (UN1/J111) and the DADF Driver PCB (UN3/J402) - Harness between the Reader Controller PCB (UN1/J101) and the Relay PCB (UN7/J1808) - Harness between the Relay PCB (UN7/J1802) and the DC Power Supply PCB (24VA) (UN34/ J202) - Harness between the Relay PCB (UN7/J1803) and the DC Power Supply PCB (24VB) (UN35/ J2020) - Harness between the DC Power Supply PCB (24VA/24VB) (UN34/J102 and UN35/J1020) and the AC Driver PCB (UN8/J810 and J813) - Harnesses between the DC Controller PCB (UN2/J1200 and J1224) and the Relay PCB (UN7/ J1817 and J1805) - Reader Controller PCB (UN1) - DADF Driver PCB (UN3) - Relay PCB (UN7) - DC Power Supply PCB (24VA) (UN34) - DC Power Supply PCB (24VB) (UN35) - AC Driver PCB (UN8) - DC Controller PCB (UN2) [Remedy] Check/replace the related harness/cable, connector and parts. [Reference] - When an error is detected, conduction of 24 V is stopped. At power check, check if 24 V is conducted or rated voltage is output by repeating power cycling of the machine. - Before replacing the Reader Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> RSRAMRES - Before replacing the DC Controller PCB, back up the service mode data (approx. 2 min) and restore the backup data after the replacement so the data may be able to be protected. Backup: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMBUP Restoration: COPIER (LEVEL2)> FUNCTION> SYSTEM> DSRAMRES
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.