Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR1730

Code: E000-0001

Description: Fixing temperature rising error
The detected temperature of the Main Thermistor failed to reach the specified temperature at temperature rising control.
Remedy: 1. Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power. 2. Check the connector connection. (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 3. Replace the Fixing Assembly. 4. Replace the DC Controller PCB (PCB1).

Code: E001-0000

Description: Detection of overheating of Fixing Assembly
The Main Thermistor detected 250 deg C or higher for 200 msec or longer on end.
Remedy: 1. Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power. 2. Check the connector connection. (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 3. Replace the Fixing Assembly. 4. Replace the DC Controller PCB (PCB1).

Code: E001-0001

Description: Detection of overheating of Fixing Assembly
The hardware circuit detected overheating of the Main Thermistor or Sub Thermistor for 30 msec or longer.
Remedy: 1. Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power. 2. Replace the DC Controller PCB (PCB1).

Code: E001-0002

Description: Detection of overheating of Fixing Assembly
The Sub Thermistor detected 295 deg C or higher for 200msec or longer on end.
Remedy: 1. Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power. 2. Check the connector connection. (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 3. Replace the Fixing Assembly. 4. Replace the DC Controller PCB (PCB1).

Code: E002-0000

Description: Error in temperature rising of Fixing Assembly
1. The Main Thermistor detected a temperature lower than 115 deg C for 400 msec or longer on end 6.0 seconds after the Main Thermistor detected 100 deg C.
2. The Main Thermistor detected a temperature lower than 150 deg C for 400 msec or longer on end 6.0 seconds after the Main Thermistor detected 140 deg C.
Remedy: 1. The Main Thermistor detected a temperature lower than 115 deg C for 400 msec or longer on end 6.0 seconds after the Main Thermistor detected 100 deg C. 2. The Main Thermistor detected a temperature lower than 150 deg C for 400 msec or longer on end 6.0 seconds after the Main Thermistor detected 140 deg C.

Code: E003-0000

Description: Detection of fixing low temperature during printing
The Main Thermistor detected a temperature lower than 80 deg C for 200 msec or longer on end, or the Sub Thermistor detected a temperature lower than 60 deg C for 200 msec or longer on end.
Remedy: 1. Go through the following to clear the error: CLEAR > ENGIN > ERRCLR in Service Mode; then, turn OFF and then ON the power. 2. Check the connector connection. (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 3. Replace the Fixing Assembly. 4. Replace the DC Controller PCB (PCB1).

Code: E004-0000

Description: Thermistor disconnection detection error
Connector disconnection was detected for 30 msec on end.
Remedy: 1. Check the connector connection. (J206 on the DC Controller PCB, J101 on the Power Supply PCB) 2. Replace the Fixing Assembly. 3. Replace the DC Controller PCB (PCB1).

Code: E010-0001

Description: Main Motor (M2) rotation error
Detection was performed every 100 msec since the start of drive and there had been no lock detection signal in 2 seconds.
Remedy: 1. Check the connector between the Main Motor and the DC Controller PCB (J203). 2. Replace the Main Motor (M2). 3. Replace the DC Controller PCB (PCB1).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie