Description: Main Motor (M2) rotation error
Detection was performed every 100msec during the drive (after the lock detection) and the lock signal was not detected 5 times in a row (in 500 msec).
Remedy: 1. Check the connector between the Main Motor and the DC Controller PCB (J203). 2. Replace the Main Motor (M2). 3. Replace the DC Controller PCB (PCB1).
Description: Error in rotation of Waste Toner Motor (M3)
Lock detection flag was monitored every 2msec, and the same level was detected 600 times in a row.
Remedy: 1. Check the connector connection between the Waste Toner Motor and the DC Controller PCB (J209). 2. Replace the Waste Toner Motor (M3). 3. Replace the DC Controller PCB (PCB1).
Description: Fixing Motor (M1) rotation error
Detection was performed every 100 msec since the start of drive and there had been no lock detection signal in 2 seconds.
Remedy: 1. Check the connector connection between the Fixing Motor and the DC Controller PCB (J203). 2. Replace the Fixing Motor (M1). 3. Replace the DC Controller PCB (PCB1)
Description: Fixing Motor (M1) rotation error
Detection was performed every 100 msec during the drive (after the lock detection) and the lock signal was not detected 5 times in a row (in 500 msec).
Remedy: 1. Check the connector connection between the Fixing Motor and the DC Controller PCB (J203). 2. Replace the Fixing Motor (M1). 3. Replace the DC Controller PCB (PCB1).
Description: Fixing Motor (M1) pressure release error
Pressure release had never been detected in 3.0 seconds.
Remedy: 1. Check the connector connection between the Fixing Motor and the DC Controller PCB (J203). 2. Replace the Fixing Motor (M1). 3. Replace the DC Controller PCB (PCB1).
Description: Fixing Motor (M1) pressurization error
Pressurization had never been detected in 3.0 seconds
Remedy: 1. Check the connector connection between the Fixing Motor and the DC Controller PCB (J203). 2. Replace the Fixing Motor (M1). 3. Replace the DC Controller PCB (PCB1).
Description: Detection of toner clog between the Hopper and the Developing Assembly
When the Developing Assembly Toner Sensor (TS2) detected "toner absent" and the Hopper Toner Sensor (TS1) detected "toner-present", the Hopper Motor (M6) was rotated 194 times with intermissions of 1 second, but the Developing Assembly Toner Sensor (TS2) could not detect "toner-present". * If paper is being fed, the error occurs after the paper has been delivered.
Remedy: 1. Check rotation of the Hopper Motor Gear. (If it is rotating, the sensor may not be detecting correctly. In that case, execute Service Mode>CLEAR>ENGIN>TNRINST to supply toner to the Developing Assembly.) 2. Replace the Developing Assembly Toner Sensor (TS2). 3. Replace the Hopper Toner Sensor (TS1). 4. Replace the DC Controller PCB (PCB1).
Description: Connector disconnection of the Developing Assembly Toner Sensor (TS2) or the DC Controller PCB (J209)
Developing Assembly Toner Sensor (TS2) connection detection signals were not detected 10 times in a row in 100 msec. * If paper is being fed, the error occurs after the paper has been delivered.
Remedy: 1. Check the connection of the Connector (J209). 2. Replace the Developing Assembly Toner Sensor (TS2). 3. Replace the DC Controller PCB (PCB1).
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.