Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Canon iR3320 — Trang 5/15

Code: E302-0002

Description: During stream reading, the edge white addition processing does not end on the rear controller PCB after 10 sec
Causes: The CCD PCB is faulty. The wiring is faulty (short circuit, open circuit). The reader controller PCB is faulty
Remedy: 1. Connector Are the connectors (J6001/J6002) on the CCD PCB and the connectors (J5002/J5003) on the reader controller PCB connected securely? NO: Connect the connectors securely. 2. CCD unit Try replacing the CCD unit. Is the problem corrected? YES: End. 3. Reader controller PCB, Main controller PCB Try replacing the reader controller PCB. Is the problem corrected? YES: End. NO: Check the wiring; if normal, replace the main controller PCB.

Code: E315

Description: Any of the following is true in the image processing by the main controller:
The image data has a fault The encoding/decoding operation for image data has a fault The image processing element of the main controller PCB has a fault
Causes: The image data is faulty. The main controller PCB is faulty. The HDD is faulty.
Remedy: If this error occurs during normal copying or printing, the job in question (image data) is cleared when the main power switch is turned off and then on again; i.e., the machine will be reset. If this error occurs frequently, however, a fault on the main controller PCB is a possibility. Further, if this error occurs in a specific image within the MAIL BOX, damage in data may be assumed; be sure to delete the image from the MAIL BOX.

Code: E420-0001

Description: When the power switch of the host machine is turned on, the back-up data from the EEPROM cannot be read or the data that has been read has a fault
Causes: The EEPROM is faulty. The ADF controller PCB is faulty.
Remedy:

Code: E421-0001

Description: The back-up data cannot be written to the EEPROM, or the data that has been written has a fault
Causes: The EEPROM has a fault. The ADF controller PCB has a fault.
Remedy:

Code: E422-0001

Description: While the ADF is in standby, the communication with its host machine is disrupted for 5 sec or more; or, while the ADF is in operation, the communication with its host machine is disrupted for 0.5 sec or more
Causes: The IPC communication is faulty. The communication line has an open circuit. The ADF controller PCB is faulty.
Remedy:

Code: E500-0000

Description: The communication between the copier and the finisher is disrupted and is not corrected for 5 sec or less
Causes: The copier harness is faulty. (disconnected connector, open circuit) The finisher controller PCB or the copier’s DC controller PCB is faulty.
Remedy:

Code: E501-0001

Description: The communication between the finisher controller PCB and the puncher drive PCB is disrupted
Causes: The finisher controller PCB is faulty. The puncher drive PCB is faulty.
Remedy:

Code: E505-0001

Description: When the main power is turned on, the checksum of the finisher controller PCB has a fault
Causes: The EEPROM is faulty. The finisher controller PCB is faulty. The puncher driver PCB is faulty.
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie