Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Epson AcuLaser C9000 — Trang 4/6

Code: E408

Description: New transfer belt unit release error. When a new product status is not cleared after a new Transfer Belt Unit has been set.
Causes: • Control Board (PWB-A)
Remedy: 1 Remove the Unit and set it again. 2 Replace the PWB-A.

Code: E500

Description: Fuser warm-up error (Heat Roll Lamp). When warm-up is not completed since the Heat Roller Thermistor does not detect the specified temperature if the predetermined has elapsed time after a start of warm-up.
Causes: • Fuser Unit • Heater Lamp Control Board (PWB-T) • Power Supply (PU1) • Control Board (PWB-A)
Remedy: 1 Replace the Fuser Unit. 2 Replace the PWB-T. 3 Replace the PWB-A. 4 Replace the PU1.

Code: E501

Description: Fuser warm-up error (Pressure Roll Lamp). When warm-up is not completed since the Pressure Roller Thermistor does not detect the specified temperature if the predetermined time has elapsed after a start of warm-up.
Causes: • Fuser Unit • Heater Lamp Control Board (PWB-T) • Power Supply (PU1) • Control Board (PWB-A)
Remedy: 1 Replace the Fuser Unit. 2 Replace the PWB-T. 3 Replace the PWB-A. 4 Replace the PU1.

Code: E510

Description: Extremely low fuser temperature (Heat Roll Lamp). When the temperature detected by the Heat Roller Thermistor drops below the specified temperature for longer than the predetermined time.
Causes: • Fuser Unit • Heater Lamp Control Board (PWB-T) • Power Supply (PU1) • Control Board (PWB-A)
Remedy: 1 Replace the Fuser Unit. 2 Replace the PWB-T. 3 Replace the PWB-A. 4 Replace the PU1.

Code: E511

Description: Extremely low fuser temperature (Pressure Roll Lamp). When the temperature detected by the Pressure Roller Thermistor drops below the specified temperature for longer than the predetermined time.
Causes: • Fuser Unit • Heater Lamp Control Board (PWB-T) • Power Supply (PU1) • Control Board (PWB-A)
Remedy: 1 Replace the Fuser Unit. 2 Replace the PWB-T. 3 Replace the PWB-A. 4 Replace the PU1.

Code: E520

Description: Extremely high fuser temperature (Heat Roll Lamp). When the temperature detected by the Heat Roller Thermistor rises above the specified temperature for longer than the predetermined time.
Causes: • Fuser Unit • Heater Lamp Control Board (PWB-T) • Power Supply (PU1) • Control Board (PWB-A)
Remedy: 1 Replace the Fuser Unit. 2 Replace the PWB-T. 3 Replace the PWB-A. 4 Replace the PU1.

Code: E521

Description: Extremely high fuser temperature (Pressure Roll Lamp). When the temperature detected by the Pressure Roller Thermistor rises above the specified temperature for longer than the predetermined time.
Causes: • Fuser Unit • Heater Lamp Control Board (PWB-T) • Power Supply (PU1) • Control Board (PWB-A)
Remedy: 1 Replace the Fuser Unit. 2 Replace the PWB-T. 3 Replace the PWB-A. 4 Replace the PU1.

Code: E530

Description: New Fuser Unit release error. When a new product status is not cleared after a new Fuser Unit has been set.
Causes: • Control Board (PWB-A)
Remedy: 1 Remove the Unit and set it again. 2 Replace the PWB-A.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie