Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP DesignJet T830 MFP — Trang 15/16

Code: 0059-0289

Description: NVM backup is missing or does not work correctly (NVM location, see Locations of the PCAs).
Causes:
Remedy: Remote troubleshooting (call agent) Restart the unit. If the problem persists, then:Onsite troubleshooting and solution (service engineer)1. Remove left cover, see Left Cover MFP SV Kit F9A30-67012, and ensure NVM backup cable is properly connected to it and to the Main PCA.2. Replace the NVM backup.

Code: 0081-0008

Description: 81.00. Media advance
Causes: 08. JAM
Remedy:

Code: 0085-0101

Description: Feed index encoder sensor does not work properly
Causes: Feed Encoder Disk, Main PCA
Remedy: Remote troubleshooting (call agent)1. Switch off the printer, and disconnect the power cord. Reconnect the power cord and power on the printer.2. The call agent should arrange a service engineer visit to change the Feed Index PCA and follow onsite troubleshooting below. Feed Index encoder sensor PCA3. If a different system error is displayed then the call agent should perform the applicable troubleshooting procedure.Onsite troubleshooting and solution (service engineer)1. Remove the covers and check that all the cables are well connected to the Main PCA, and none of them are damaged. If any cable is not connected then reconnect it, and power on the printer again to check whether the system error has disappeared.IMPORTANT:If any cable is damaged then order a Cable Service Kit: Cables Sk2. Replace the Feed Index Encoder Sensor PCA, see Encoder PCA and Index Feed Index encoder sensor PCA3. Check that the Encoder Disk is not dirty or damaged. If the Encoder Disk is damaged, it should be replaced, see Encoder Disk. Encoder Disk

Code: 0085-0201

Description: Feed encoder sensor does not work properly
Causes: Feed encoder Disk, Main PCA
Remedy: Remote troubleshooting (call agent)1. Switch off the printer, and disconnect the power cord. Reconnect the power cord and power on the printer.2. The call agent should arrange a service engineer visit to change the Feed encoder sensor PCA. Feed Encoder Sensor PCA3. If a different system error is displayed then the call agent should perform the applicable troubleshooting procedure.Onsite troubleshooting and solution (service engineer)1. Remove the covers and check that all the cables are well connected to the Main PCA, and none of them are damaged. If any cable is not connected then reconnect it, and power on the printer again to check whether the system error has disappeared.IMPORTANT:If any cable is damaged then order a Cable Service Kit: Cables Sk2. Replace the Feed Encoder Sensor PCA, see Encoder PCA and Index. Feed Encoder Sensor PCA3. Check that the Encoder Disk is not dirty or damaged. If the Encoder Disk is damaged it should be replaced, see Encoder Disk. Encoder Disk.

Code: 0086-0008

Description: 86.00. Scan axis jam
Causes: 08. JAM
Remedy:

Code: 0087-0001

Description: Encoder Strip failure
Causes: Carriage (encoder sensor)
Remedy: Remote troubleshooting (call agent)1. Switch off the printer, and disconnect the power cord. Reconnect the power cord and power on the printer.2. The call agent should arrange a service engineer visit to change the Encoder Strip and follow onsite troubleshooting below. Encoder Strip (36)3. If a different system error is displayed then the call agent should perform the applicable troubleshooting procedure.Onsite troubleshooting and solution (service engineer)1. Remove the covers and check that Encoder Strip is not broken or dirty. Cables Sk2. If the Encoder Strip is dirty, follow the procedure in this manual to clean it, see Clean the Encoder Strip. 3. If the Encoder strip is damaged or does not work, it should be replaced, see Encoder Strip. 4. If this fails to solve the issue, the problem might be due to the encoder sensor within the carriage. In that case, replace the carriage, see Carriage and Belt.

Code: 0153-0302

Description: Multi-Sheet Tray presence not detected
Causes: MPCA
Remedy: Remote troubleshooting (call agent) Ensure that the Multi-Sheet Tray is properly placed and the latch is closed.Onsite troubleshooting and solution (service engineer) Ensure that the Multi-Sheet Tray sensor cable is correclty connected to the MPCA, checking the J27 connector in the MPCA.

Code: 0227-0046

Description: 27.00. Printhead
Causes: 46. NOT CALIBRATED MISSALIGNED UNABLE TO CALIBRATE
Remedy:
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie