Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi HP DesignJet T830 MFP — Trang 16/16

Code: 0824-0100

Description: 24.01. Ink Blockage Long Repumps
Causes: Last 4 bits interpreted as 0=working 1=not working, order is KCMY
Remedy:

Code: 0824-0200

Description: 24.02. Ink Blockage Delays Phase
Causes: Last 4 bits interpreted as 0=working 1=not working, order is KCMY
Remedy:

Code: 0824-0300

Description: 24.03. Ink Blockage Bag Cycling Phase
Causes: Last 4 bits interpreted as 0=working 1=not working, order is KCMY
Remedy:

Code: 0824-2000

Description: 24.20. SHAID (Ink detection sensor inside PHA) not covered
Causes: Last 4 bits interpreted as 0=working 1=not working, order is KCMY
Remedy:

Code: 0824-XXXX

Description: IDS startup problem: Silent System Errors not shown in the Front Panel. Refer to Ink supplies troubleshooting for more information, see Ink-supplies troubleshooting. See Error messages related with printhead and start-up for additional error codes.
Causes:
Remedy:

Code: 0942-0188

Description: 42.01. Carriage motor
Causes: 88. Carriage homing problem
Remedy:

Code: 0942-0188

Description: Carriage homing problem
Causes:
Remedy: Remote troubleshooting (call agent)1. Reboot the unit. If the problem persists, clean the encoder strip, see Clean the Encoder Strip. 2. If the issue is not solved, open the PHA door and check if there’s any paper strips blocking either the carriage or the SVS.3. Go to Diagnostic Menu, see Entering the support menus and run Carriage Servo diagnostic, see 4.3 Carriage servo. Onsite troubleshooting and solution (service engineer)1. Check encoder strip, scan axis and service station parts.2. Depending on the failing subsystem, any one of them may need replacing.

Code: 0955-0050

Description: Line sensor failure
Causes: Carriage PCA, Trailing Cable, Main PCA
Remedy: Remote troubleshooting (call agent)1. Switch off the printer, and disconnect the power cord. Reconnect the power cord and power on the printer.2. The call agent asks the customer to go to Support Menu by pressing the Power key continuously for 15 seconds.3. Go to Diagnostic Menu and run the Line Sensor diagnostic, see 4.7 Line Sensor (or ZIM, Spot sensor). 4. The call agent should arrange a service engineer visit to change the Line Sensor assembly; follow the onsite troubleshooting below. Line Sensor5. If a different system error is displayed then the call agent should perform the applicable troubleshooting procedure.Onsite troubleshooting and solution (service engineer)1. Go to Support Menu (see Entering the support menus) and run the Line Sensor diagnostic, see 4.7 Line Sensor (or ZIM, Spot sensor). 2. Remove the covers and check that the cable of the line sensor is connected to the Carriage PCA and it is not damaged. If the cable is not connected then reconnect it, and power on the printer again to check whether the error has disappeared.IMPORTANT:If the cable is damaged then replace the Line Sensor, see Carriage Line Sensor. Line Sensor3. Clean the Line Sensor and try again, see Clean the Carriage Line Sensor. 4. Replace the Carriage Assembly, see Carriage and Belt. Carriage assembly w/belt (36)5. Replace the Main PCA, see Main PCA Main PCA
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie