• Code: 57.00.10
• Display: 57.00.10 Error To continue turn off then on
• Description: Duplex fan (FM-2001) malfunction
• Remedy: 1. Turn the product off, and then on. 2. Remove and reinstall the duplex unit to ensure a proper connection. 3. If the error persists, replace the duplex unit.

• Code: 59.00.30
• Display: 59.00.30
• Description: A printer motor error occurred. Fuser motor error.
  Fuser motor start up error
• Remedy: 1. Turn the product off, and then on. 2. Check the fuser for any jammed media that might be restricting proper movement of the fuser rollers. 3. Remove and reinstall the fuser. 4. Run the fuser motor test in the actuator drive mode to make sure that the fuser motor is functioning correctly. If it is not, replace the fuser motor. 5. Check the connector (J59) of the fuser motor and connector (J233) on the DC controller PCA. 6. If the error persists, replace the fuser motor. 7. If the error persists, replace the fuser assembly. 8. If the error persists, replace the fuser drive assembly.

• Code: 59.00.40
• Display: 59.00.40
• Description: A printer motor error occurred. Fuser motor error.
  Fuser motor rotation error
• Remedy: 1. Turn the product off, and then on. 2. Check the fuser for any jammed media that might be restricting proper movement of the fuser rollers. 3. Remove and reinstall the fuser. 4. Run the fuser motor test in the actuator drive mode to make sure that the fuser motor is functioning correctly. If it is not, replace the fuser motor. 5. Check the connector (J59) of the fuser motor and connector (J233) on the DC controller PCA. 6. If the error persists, replace the fuser motor. 7. If the error persists, replace the fuser assembly. 8. If the error persists, replace the fuser drive assembly.

• Code: 59.05.50
• Display: 59.05.50
• Description: A printer motor error occurred. Main motor error.
  Drum motor start up error
• Remedy: 1. Turn the product off, and then on. 2. Run the drum motor test in the actuator drive mode to make sure that the drum motor is functioning correctly. If it is not, replace the drum motor. 3. Check the connector (J60) of the drum motor and connector (J222) on the DC controller PCA. 4. If grinding or clicking noises occur with the error, there might be other parts of the drive assembly causing the issue. • Registration assembly • Drum feed drive assembly • PIU of Tray 2 and Tray 3 5. If this is the suspected cause and the exact part causing the issue cannot be determined, all three parts should be replaced at the same time. 6. If no noises are associated with the error and the drum motor has already been replaced, replace the DC controller.l

• Code: 59.05.60
• Display: 59.05.60
• Description: A printer motor error occurred. Main motor error.
  Drum motor rotation error
• Remedy: 1. Turn the product off, and then on. 2. Run the drum motor test in the actuator drive mode to make sure that the drum motor is functioning correctly. If it is not, replace the drum motor. 3. Check the connector (J60) of the drum motor and connector (J222) on the DC controller PCA. 4. If grinding or clicking noises occur with the error, there might be other parts of the drive assembly causing the issue. • Registration assembly • Drum feed drive assembly • PIU of Tray 2 and Tray 3 5. If this is the suspected cause and the exact part causing the issue cannot be determined, all three parts should be replaced at the same time. 6. If no noises are associated with the error and the drum motor has already been replaced, replace the DC controller.l

• Code: 60.00.02
• Display: 60.00.02 Tray 2 lifting error
• Description: Lifter driver assembly Tray 2 failure A tray lift motor error has occurred.
• Remedy: 1. On the product control panel, open the following menus: • Administration • Troubleshooting • Diagnostic Tests 2. Use the Tray/Bin manual sensor test to make sure that the Tray 2 paper (PS1409 and PS1410) surface sensors are functioning correctly. 3. If this part has been removed or replaced, check the connector (J221) on the DC controller PCA and interconnect J21. 4. If the error persists, replace the lifter drive assembly (Tray 2).

• Code: 60.00.03
• Display: 60.00.03 Tray 3 lifting error
• Description: Lifter driver assembly Tray 3 failure A tray lift motor error has occurred.
• Remedy: 1. On the product control panel, open the following menus: • Administration • Troubleshooting • Diagnostic Tests 2. Use the Tray/Bin manual sensor test to make sure that the Tray 3 paper (PS1411 and PS1412) surface sensors are functioning correctly. 3. If this part has been removed or replaced, check the connector (J221) on the DC controller PCA and interconnect J21. 4. If the error persists, replace the lifter drive assembly (Tray 3).e d

• Code: 60.00.04
• Display: 60.00.04 Tray 4 lifting error
• Description: Lifter driver assembly Tray 4 failure A tray lift motor error has occurred.
• Remedy: 1. On the product control panel, open the following menus: • Administration • Troubleshooting • Diagnostic Tests 2. Use the Tray/Bin manual sensor test to make sure that the Tray 4 paper (PS3101 and PS3103) surface sensors are functioning correctly. 3. If this part has been removed or replaced, check the connector (J3005) on the HCI controller PCA J906. 4. If the error persists, replace the lifter drive assembly (Tray 4).y (T