Code :

Code: CD201, CD202, CD203
Description: • CD201: File memory mounting error • CD202: Memory capacity discrepancy • CD203: Memory capacity discrepancy 2. CD201: • The file memory is not mounted. • The file has any abnormality. CD202: • File memory capacity on the MFP board (MFPB) is not enough. • File memory capacity necessary for duplex printing is not enough. CD203: File memory capacity on the MFP board (MFPB) is not enough.
Causes: • MFP board (MFPB) • Memory board (MEMB; UK-211)
Remedy: 1. Check to see if MEMB on MFPB is installed correctly. 2. Replace MEMB on MFPB. 3. Replace MFPB.

Code: CD211, CD212
Description: • CD211: PCI-SDRAM DMA operation failure • CD212: Compression/extraction timeout detection. • CD211: Hardware related to the transfer of memory image of the MFP board (MFPB) fails to respond. • CD212: Hardware related to the BTC compression function of the MFP board (MFPB) fails to respond.
Causes: MFP board (MFPB)
Remedy: 1. Replace MFPB.

Code: CD241, CD242
Description: CD241: Encryption ASIC setting error CD242: Encryption ASIC mounting error. CD241: Initialization error of the encrypted ASIC is detected during the machine is starting. CD242: The faulty of the installation of encrypted ASIC is detected during the machine is starting.
Causes: MFP board (MFPB)
Remedy: 1. Check the MFP board connector for proper connection and correct as necessary. 2. Replace MFPB

Code: CD252
Description: No relay circuit boards for IC-416 mounting at IC-416 mount setting. EFI relay circuit boards (VI-508) are not mounted when the IC-416 is set to mount setting at Service Mode.
Causes: • MFP board (MFPB) • EFI relay board (VI-508)
Remedy: 1. If the IC-416 is not mounted, access [Service Mode] -> [System 2] -> [Image Controller Setting] and check to see if “Controller 0” is set for the image controller. 2. Check the EFI relay board (VI-508) connector for proper connection and correct as necessary. 3. Replace EFI relay board (VI-508). 4. Replace MFPB.

Code: CD261
Description: USB host board failure. • When a failure is detected in USB host board included in the local interface kit. • Non-standard USB device is connected.
Causes: • MFP board (MFPB) • USB host board (EK-608) • USB host board (EK-609)
Remedy: 1. Check the operation with another USB device. 2. Check the USB host board connector for proper connection and correct as necessary. 3. Replace the USB host board. 4. Replace MFPB.

Code: CD262
Description: Extension network adapter installation error. • When the 2nd network card settings is set to “Set” but the upgrade kit (UK-212) is not installed. • Upgrade Kit (UK-212) is faulty.
Causes:
Remedy: 1. Check the settings of [Service Mode] -> [Network Settings] -> [2nd Network Setting] -> [2nd network card settings]. 2. Check the UK-212 connector for proper connection and correct as necessary. 3. Rewrite the firmware. 4. Reinstall the UK-212.

Code: CD271
Description: i-Option activated and additional memory not installed. While the i-Option is activated, the additional memory included in UK-211 is not installed.
Causes: • MFP board (MFPB) • Memory board (MEMB; UK-211)
Remedy: 1. Check MEMB for proper connection and correct as necessary. 2. Replace MEMB. 3. Replace MFPB.

Code: CD272
Description: i-Option activated and additional memory and HDD not installed. While the i-Option is activated, the additional memory included in UK-211 and the HDD are not installed.
Causes: • MFP board (MFPB) • Hard disk (A) (HDD (A)) • Memory board (MEMB; UK-211)
Remedy: 1. Check MEMB for proper connection and correct as necessary. 2. Access [Service Mode] -> [System 2] -> [HDD] and check to see if “Installed” is selected. 3. Replace MEMB. 4. Replace the hard disk (A). 5. Replace MFPB.