Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub C652DS — Trang 27/28

Code: CD231

Description: No Fax memory at FAX board mounting
Causes: MFP board (MFPB) FAX board
Remedy: 1 Check to see if the FAX board is installed correctly. - - 2 Change PRCB.

Code: CD241, CD242

Description: CD241: Encryption ASIC setting error CD242: EncryptionASIC mounting error
Causes: MFP board (MFPB)
Remedy: 1 Check the MFP board connector for proper connection and correct as necessary. - - 2 Change MFPB

Code: CD252

Description: No relay circuit boards for IC-412 mounting at IC-412 mount setting
Causes: MFP board (MFPB) Relay circuit boards (VI-505)
Remedy: 1 If the IC-412 is not mounted, access [Service Mode] - [System 2] - [Image Controller Setting] and check to see if gController 0h is set for [Image Controller Setting]. . . 2 Check the relay board (VI-505) connector for proper connection and correct as necessary. . . 3 Change relay board (VI-505). . . 4 Change MFPB.

Code: CD261

Description: USB host board failure
Causes: MFP board (MFPB) USB host board (EK-604)
Remedy: 1 Check the operation with another USB device. - - 2 Check the USB host board connector for proper connection and correct as necessary. - - 3 Change USB host board. - - 4 Change MFPB.

Code: CD271

Description: i-Option activated and additional memory not installed
Causes: MFP board (MFPB) Memory for i-Option (UK-203)
Remedy: 1 Check the memory (UK-203) for proper connection and correct as necessary. - - 2 Change memory (UK-203). - - 3 Change MFPB.

Code: CD272

Description: i-Option activated and additional memory and HDD not installed
Causes: MFP board (MFPB) Hard disk Memory for i-Option (UK-203)
Remedy: Check the memory (UK-203) for proper connection and correct as necessary. - - 2 Check the HDD for proper connection and correct as necessary. - - 3 Change memory (UK-203). - - 4 Change HDD - - 5 Change MFPB.

Code: CD3##

Description: NVRAM data error
Causes:
Remedy: . When the data stored due to the NVRAM trouble is lost, backup data can be used for restoration. . Trouble code [C-D370] will be displayed when multiple errors (over 5) of NVRAM data are detected, which can be restored with one restoration command. . Data backup will be automatically performed every hour. Backup can also be performed manually with the following setting. [Service Mode] - [Enhanced Security] - [NVRAM Data Back Up] 1. When a trouble caused by NVRAM data error occurs, the screen below appears. 2. Select [Yes] and touch [OK]. 3. The screen will be shifted to the data restoration screen to perform data restoration. NOTE • When the restoration is performed in a short time, data restoration screen may not be displayed. 4. Check the message which indicates that the data restoration was successfully conducted. Turn OFF the main power switch and turn it ON again more than 10 seconds after. NOTE • In case it failed to restore data, return to the trouble code screen.

Code: CD401...CD407

Description: CD401: NACK command incorrect CD402: ACK command incorrect CD403: Checksum error CD404: Receiving packet incorrect CD405: Receiving packet analysis error CD406: ACK receiving timeout CD407: Retransmission timeout
Causes: MFP board (PRCB)
Remedy: 1 Check whether there is an strong electromagnetic noise source near the main body. - - 2 Check the connectors on MFPB for proper connection and correct as necessary. - - 3 Change MFPB.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie