Description: MFP control board cooling fan's failure to turn The fan lock signal remains HIGH for a predetermined continuous period of time while the fan remains stationary.
Causes: • MFP control board cooling fan (FM17) • MFP board (MFPB)
Remedy: 1 Check the connector between FM17-MFPB PJ26 for proper connection and correct as necessary. 2 Check the fan for possible overload and correct as necessary. 3 FM17 operation check MFPB PJ26-3 (LOCK) 21-O. 4 Replace FM17. 5 Replace MFPB.
Description: MFP control board CPU temperature failure Temperature failure of CPU on the MFP board was detected.
Causes: • CPU cooling fan (FM104) • MFP board (MFPB)
Remedy: 1 Reboot the machine. 2 Check the connector between FM104-MFPB PJ20 for proper connection and correct as necessary. 3 Check the fan for possible overload and correct as necessary. 4 FM104 operation check MFPB PJ20 17-S. 5 Replace FM104. 6 Replace MFPB.
Description: Engine control error The port monitor control detects engine control error.
Causes: Printer control board (PRCB)
Remedy: 1 Check the connectors of the printer control board (PRCB) for proper connection, and correct as necessary. 2 Rewrite the firmware. 3 Replace PRCB.
Description: Drive system home sensor malfunction • The scanner home sensor is unable to detect the scanner located at its home position. • The scanner home sensor is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. • The scanner home sensor detects the scanner when the scanner has moved the maximum travelling distance from the position, at which it blocks the scanner home sensor.
Causes: • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB)
Remedy: 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the PS201, M201, SCDB and MFPB connector for proper connection and correct as necessary. 5 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 17-V. 6 M201 operation check SCDB PJ4-1 to 7 17-V. 7 Replace SCDB. 8 Replace MFPB.
Description: Slider over running The scanner home sensor detects the scanner at its home position during a period of time that begins with the time when a pre-scan command and a scan preparation command are executed and ends when a home return command is executed.
Causes: • Scanner home sensor (PS201) • Scanner motor (M201) • Scanner drive board (SCDB) • MFP board (MFPB)
Remedy: 1 Correct or change the scanner drive (pulley, gear, belt) if it is faulty. 2 Correct the scanner motor set screw if loose. 3 Adjust [Image Position Leading Edge] and [Feed Direction Adjustment]. 4 Check the PS201, M201, SCDB and MFPB connector for proper connection and correct as necessary. 5 PS201 I/O check, sensor check SCDB PJ6-3 (ON) 17-V. 6 M201 operation check SCDB PJ4-1 to 7 17-V. 7 Replace SCDB. 8 Replace MFPB.
Description: Back side cleaning home sensor abnormality (initial) • The back side cleaning home sensor (PS9) does not change from H to L even after the lapse of a given period of time after the home position detecting operation is started at the initial operation. • The back side cleaning home sensor (PS9) does not change from L to H even after the lapse of a given period of time after the home position detecting operation is started at the initial operation.
Causes: • Back side cleaning home sensor (PS9) • Back side cleaning motor (M7) • DF control board (DFCB)
Remedy: 1 Check the connector between M7-relay CN119-DFCB CN6 for proper connection, and correct as necessary. 2 Check the connector of M7 for proper drive coupling, and correct as necessary. 3 PS9 I/O check, sensor check DFCB CN3-11 (ON) DF-702 6-C. 4 M7 operation check DFCB CN6-5 to 8 DF-702 7-C. 5 Replace M7. 6 DFCB ICP4 conduction check. 7 Replace DFCB.
Description: Back side cleaning home sensor abnormality (normal) At the time of operation other than the initial operation, the back side cleaning home sensor (PS9) error is detected.
Causes: • Back side cleaning home sensor (PS9) • Back side cleaning motor (M7) • DF control board (DFCB)
Remedy: 1 Check the connector between M7-relay CN119-DFCB CN6 for proper connection, and correct as necessary. 2 Check the connector of M7 for proper drive coupling, and correct as necessary. 3 PS9 I/O check, sensor check DFCB CN3-11 (ON) DF-702 6-C. 4 M7 operation check DFCB CN6-5 to 8 DF-702 7-C. 5 Replace M7. 6 DFCB ICP4 conduction check. 7 Replace DFCB.
Description: Image input time out Image data is not input from the scanner to the MFP board (MFPB).
Causes: • MFP board (MFPB) • CCD board (CCDB)
Remedy: 1 Select [Service Mode] - [State Confirmation] - [Memory/HDD Adj.] - [Memory Bus Check] - [Scanner-Memory], and conduct the memory bus function. 2 Check the connectors between scanner section and MFPB for proper connection and correct as necessary. 3 Replace MFPB. 4 Replace CCDB.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.