Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta bizhub Pro 1200P — Trang 6/91

Code: C-0140

Description: PI-PFU (PF-703) paper feed motor (M1) speed abnormality. An error detection signal is detected twice in succession within a specified period of time after M1 was turned ON.
Causes: Paper feed motor (M1: PF-702/703) PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 17-K 3 Replace M1. - 4 Replace PFUDB.

Code: C-0141

Description: PI-PFU (PF-703) PF exit conveyance motor (M3) power abnormality. An error detection signal (blowout of ICP) of M3 is detected when M3 is turned ON.
Causes: PF exit conveyance motor (M3: PF-703) PF drive board (PFUDB: PF-703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality, and then replace PFUDB. PF-703: 8-L 3 Replace M3 and PFUDB at a time.

Code: C-0142

Description: PI-PFU (PF-703) coupling conveyance motor /1 (M4) power abnormality. An error detection signal (blowout of ICP) of M4 is detected when M4 is turned ON.
Causes: Coupling conveyance motor /1 (M4: PF-703) PF drive board (PFUDB: PF-703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality, and then replace PFUDB. PF-703: 20-L 3 Replace M4 and PFUDB at a time.

Code: C-0143

Description: PI-PFU (PF-703) coupling conveyance motor /2 and /3 (M5 and M6) power abnormality. An error detection signal (blowout of ICP) of M5 and M6 is detected when M5 and M6 are turned ON.
Causes: Coupling conveyance motor /2 (M5: PF-703) Coupling conveyance motor /3 (M6: PF-703) PF drive board (PFUDB: PF-703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality, and then replace PFUDB. PF-703: 21-L 3 Replace PFUDB. - 4 Replace M5, M6 and PFUDB at a time.

Code: C-0144

Description: PI-PFU (PF-703) SD/CL power abnormality. At the start, the error detection signal of the PFUDB solenoid/clutch ICP blowout is detected.
Causes: PF drive board (PFUDB: PF-702/703)
Remedy: 1 Check the connector connection and the wiring on PFUDB, and repair it if any abnormality. - 2 Check the drive and the coupling of the solenoid and the clutch connected to PFUDB, repair/replace it if any abnormality, and then replace PFUDB. - 3 Replace PFUDB. - 4 If the same error cord occurs even after replacing PFUDB, replace the connected solenoid, the clutch and PFUDB at a time.

Code: C-0145

Description: PI-PFU (PF-703) paper feed belt motor (M2) speed abnormality. An error detection signal is detected twice in succession within a specified period of time after M2 was turned ON.
Causes: Paper feed belt motor (M2: PF-703) PF drive board (PFUDB: PF-703)
Remedy: 1 Check the connector connection and the wiring between PFUDB and the motor, and repair it if any abnormality. - 2 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. PF-703: 5-L 3 Replace M2. - 4 Replace PFUDB.

Code: C-0201

Description: Tray /1 up abnormality 1. When the upper limit sensor /1 (PS6) is OFF, PS6 does not turn ON within 20seconds after the tray lift-up motor /1 (M25) turns ON for lifting operation. At this time, an error detection signal (24V cut off) is detected.
Causes: Upper limit sensor /1 (PS6) Tray lift-up motor /1 (M25) Printer control board (PRCB) DC power supply /2 (DCPS /2)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate condition of the tray 1, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 5-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. 3-G 5 Replace PS6. - 6 Replace M25. - 7 Replace PRCB. - 8 Replace DCPS /2.

Code: C-0203

Description: Tray /1 up abnormality 2. When the upper limit sensor /1 (PS6) is OFF, PS6 does not turn ON within 20seconds after the tray lift-up motor /1 (M25) turns ON for lifting operation. At this time, an error detection signal is not detected.
Causes: Upper limit sensor /1 (PS6) Tray lift-up motor /1 (M25) Printer control board (PRCB) DC power supply /2 (DCPS /2)
Remedy: 1 Check the paper loaded condition and the rear end restriction plate condition of the tray 1, and repair it if any abnormality. - 2 Check the connector connection and the wiring between PRCB and motor/sensor, and repair it if any abnormality. - 3 Check the I/O drive of the motor and the coupling of the gear, and repair/replace it if any abnormality. 5-F 4 Check I/O and the operation of the sensor, and repair it if any abnormality. 3-G 5 Replace PS6. - 6 Replace M25. - 7 Replace PRCB. - 8 Replace DCPS /2.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie