• Code: C-0213#
• Description: When the upper limit sensor /1 (PS20) is OFF, PS20 does not turn ON within a specified period of time after the paper lift motor / 1 (M19) turns ON for lifting operation. And at this time, an error detection signal is not detected.
• Causes: Tray 1 paper improperly loaded Tray 1 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /1 (M19) Upper limit sensor /1 (PS20) Printer control board (PRCB) DC power supply /2 (DCPS2)

• Code: C-0220
• Description: The locking of the paper lift motor /2 (M20) is detected. When M20 is ON, an error detection signal of the M20 is detected.
• Causes: Tray 2 paper improperly loaded Tray 2 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /2 (M20) Upper limit sensor /1 (PS21) Printer control board (PRCB) DC power supply /2 (DCPS2)

• Code: C-0221#
• Description: When the upper limit sensor /2 (PS21) is OFF, PS21 does not turn ON within a specified period of time after the paper lift motor / 2 (M20) turns ON for lifting operation. And at this time, an error detection signal (24V cut off) is detected.
• Causes: Tray 2 paper improperly loaded Tray 2 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /2 (M20) Upper limit sensor /1 (PS21) Printer control board (PRCB) DC power supply /2 (DCPS2)

• Code: C-0222#
• Description: When the upper limit sensor /2 (PS21) is OFF, PS21 does not turn ON within a specified period of time after the paper lift motor / 2 (M20) turns ON for lifting operation. And at this time, an error detection signal (blowout of ICP) is detected.
• Causes: Tray 2 paper improperly loaded Tray 2 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /2 (M20) Upper limit sensor /1 (PS21) Printer control board (PRCB) DC power supply /2 (DCPS2)

• Code: C-0223#
• Description: When the upper limit sensor /2 (PS21) is OFF, PS21 does not turn ON within a specified period of time after the paper lift motor / 2 (M20) turns ON for lifting operation. And at this time, an error detection signal is not detected.
• Causes: Tray 2 paper improperly loaded Tray 2 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /2 (M20) Upper limit sensor /1 (PS21) Printer control board (PRCB) DC power supply /2 (DCPS2)

• Code: C-0230
• Description: The locking of the paper lift motor /3 (M21) is detected. When M21 is ON, an error detection signal of the M21 is detected.
• Causes: Tray 3 paper improperly loaded Tray 3 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /3 (M21) Upper limit sensor /1 (PS22) Printer control board (PRCB) DC power supply /2 (DCPS2)

• Code: C-0231#
• Description: When the upper limit sensor /3 (PS22) is OFF, PS22 does not turn ON within a specified period of time after the paper lift motor / 3 (M21) turns ON for lifting operation. And at this time, an error detection signal (24V cut off) is detected.
• Causes: Tray 3 paper improperly loaded Tray 3 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /3 (M21) Upper limit sensor /1 (PS22) Printer control board (PRCB) DC power supply /2 (DCPS2)

• Code: C-0232#
• Description: When the upper limit sensor /3 (PS22) is OFF, PS22 does not turn ON within a specified period of time after the paper lift motor / 3 (M21) turns ON for lifting operation. And at this time, an error detection signal (blowout of ICP) is detected.
• Causes: Tray 3 paper improperly loaded Tray 3 rear end restriction plate misaligned Confirmation of the wiring harness and the connector Paper lift motor /3 (M21) Upper limit sensor /1 (PS22) Printer control board (PRCB) DC power supply /2 (DCPS2)