Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta Di1610

Code: C0045

Description: Fuser fan motor error
• The LOCK signal remains HIGH or LOW continuously for a predetermined period of time while the Cooling Fan Motor remains energized.
Remedy: 1 Check the Motor connectors for connection and correct as necessary 2 Check the fan for possible overload and correct as necessary. 3 M2 operation check PWB-P MPJ13P- 1 to 3 (pulse) G to H-5 to 6 4 M3 operation check PWB-P MPJ6P-1 to 3 (pulse) E-9 to 10. 5 Replace PWB-P.

Code: C0210

Description: H. V. abnormal
• The Drum Charge Monitor Voltage (HVC_MON) signal falls outside a predetermined range at any time after the lapse of a predetermined period of time after the Power Switch has been turned ON. • The Image Transfer Voltage Monitor signal (T_MON_V) and Image Transfer Current Monitor signal (T_MON_I) fall outside a corresponding predetermined range.
Remedy: 1 Replace Fusing Unit. 2. Replace PWB-P

Code: C0500

Description: Fuser warm up error
• The voltage of the Thermistor remains low for a predetermined period of time when a warm-up cycle is started. • The temperature detected by the Thermistor remains lower than a reference value for a predetermined period of time for the period of time that begins 5 sec. after, and ends 9 sec. after, the start of the warm-up cycle (where the temperature detected by the Thermistor is 80 °C or less). • The temperature detected by the Thermistor does not increase for a 3-sec. period or more for the period of time that begins after the lapse of a predetermined period of time after the Fusing Roller Heater Lamp has been turned ON and ends when the lamp is turned OFF. • The Fusing Roller Heater Lamp remains ON for a 30sec. period or more (except during the period through which the Main Motor remains energized).
Remedy: 1 Replace Thermistor (TH1). 2 Replace Fusing Unit. 3 Replace Controller/Mechanical Control Board (PWB-P). 4 Replace Power Unit (PU1).

Code: C0510

Description: Fuser temperature low
• The temperature detected by the Thermistor remains lower than the set temperature continuously for a predetermined period of time while the fusing temperature control is being provided. (The set temperatures are as follows: 140 °C during a print mode at 600 dpi; 70 °C during the standby mode.)
Remedy: 1 Replace Thermistor (TH1). 2 Replace Fusing Unit. 3 Replace Controller/Mechanical Control Board (PWB-P). 4 Replace Power Unit (PU1).

Code: C0520

Description: Fuser overheat
• The temperature detected by the Thermistor remains higher than 235 °C for a predetermined period of time while the fusing temperature control is being provided.
Remedy: 1 Replace Thermistor (TH1). 2 Replace Fusing Unit. 3 Replace Controller/Mechanical Control Board (PWB-P). 4 Replace Power Unit (PU1).

Code: C0650

Description: Scanner home sensor error
• The Scanner Home Position Sensor is not detected within the predetermined period of time after the Scanner Motor has started turning.
Remedy: 1 M4 operation check. 2 Replace PWB-P.

Code: C1200

Description: ASIC memory abnormal
• An error occurred while writing to or reading the SRAM on the Control Board (PWB-C).
Remedy: 1 Turn the copier off, then on again. 2 Check the connection of the memory on the PWB-P, and then correct it if necessary. 3 Replace PWB-P.

Code: C1300

Description: Polygon mirror motor error
• The LOCK signal is not detected within a predetermined period of time that begins 1 sec. after the Polygon Motor has been energized. • No new LOCK signal is detected for a 1-sec. period that begins 1.5 sec. after the first LOCK signal was detected. • The LOCK signal is not detected for a continuous 0.5sec. period in a state in which the Polygon Motor runs stably. • The LOCK signal remains ON for a continuous 5-sec. period or more when the Polygon Motor remains deenergized.
Remedy: 1 Check cables for connection and correct as necessary. 2 Replace PH Unit. 3 Replace PWB-P.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie