Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Konica-Minolta Di3010 — Trang 6/7

Code: C0BC2

Description: Crease Motor Drive Failure
Remedy:

Code: C0F32

Description: ATDC Sensor Failure
• The scanning value of the ATDC Sensor is less than 7% while the Imaging Unit Motor is turning. • The scanning value of the ATDC Sensor is more than 19% while the Imaging Unit Motor is turning.
Remedy: 1 Check the ATDC sensor connector for proper connection, and correct as necessary. 2 Remove the Developing Unit from the Imaging Unit, and then replace UN2. 3 Run F8. 4 Replace PWB-A. 5 Replace PU1.

Code: C0F33

Description: ATDC Adjustment Failure
• The adjustment of the ATDC control voltage could not be completed in the set period of time when function F8 is run. • The ATDC control voltage was not within the range of 5.39 V to 8.15 V when function F8 is run.
Remedy: 1 Check the ATDC sensor connector for proper connection, and correct as necessary. 2 Remove the Developing Unit from the Imaging Unit, and then replace UN2. 3 Run F8. 4 Replace PWB-A. 5 Replace PU1.

Code: C12D0

Description: MIO Device Failure
• The MIO device does not operate properly.
Remedy: 1 Turn OFF, then ON, the power. 2 Check the CLAN Board connectors for proper connection and correct as necessary. 3 Check the MFB3 Board connectors for proper connection and correct as necessary. 4 Change the CLAN Board. 5 Change the MFB3 Board.

Code: C1300

Description: Polygon Motor Failure
• The Polygon Motor Lock signal could not be detected within the set period of time after the Polygon Motor is energized. (Faulty start detection) • No First Lock signals are detected during the 1second period that starts 1 second after a First Lock signal. (Faulty lock signal detection) • The Polygon Motor Lock signal could not be detected after the set period of time has elapsed while the Polygon Motor is turning. (Out-of-timing lock detection) • The Polygon Motor Lock signal is set to ON for longer than the set period of time while the Polygon Motor remains stopped. (Abnormal lock detection)
Remedy: 1 Check the PH connector for proper connection, and correct as necessary. 2 Replace PH Unit. 3 Replace PWB-A.

Code: C1330

Description: Main Unit Communication Failure
• Communications with the Master Board and the MFB3 Board fail.
Remedy: 1 Check the MFB3 Board connector for proper connection, and correct as necessary. 2 Check the PWB-A Board connector for proper connection, and correct as necessary. 3 Check the flat cable between MFB3 and lPWB-A for proper connection, and correct as necessary. 4 Turn the copier off, then on again. 5 Replace the MFB3 Board. 6 Replace the PWB-A Board.

Code: C133A

Description: Main Unit G/A Communication Failure
• Communications with the gate array for expansion I/O (the IC mounted on the Master Board) fail.
Remedy: 1 Turn the copier off, then on again. 2 Check each control board and the Master Board for proper connection, and correct as necessary. 3 Replace the Master Board if necessary.

Code: C133B

Description: Exit Option Paper Transport Failure
• The connection status of a finishing option is changed after the copier has been turned on.
Remedy: 1 Turn the copier off, then on again. 2 Check each control board and the Master Board for proper connection, and correct as necessary. 3 Replace the appropriate Control Board and the Master Board if necessary.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie