Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Kyocera FS9500DN — Trang 3/9

Code: 2000

Description: Drive motor problem
• LOCK ALM signal remains high for 1 s, 1 s after the drive motor has turned on.
Causes: Poor contact in the drive motor connector terminals. Defective drive motor rotation control circuit. Defective drive transmission system.
Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.

Code: 2500

Description: Paper feed motor problem
• LOCK ALM signal remains high for 1 s, 1 s after the paper feed motor has turned on.
Causes: Poor contact in the paper feed motor connector terminals. Defective paper feed motor rotation control circuit. Defective drive transmission system.
Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the paper feed motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.

Code: 2600

Description: Deck conveying motor/desk drive motor problem
• No pulse is input within 500 ms of the start-up. • No pulse is input within 100 ms of the previous pulse input.
Causes: Defective deck conveying motor board/desk drive motor board. Deck conveying motor /desk drive motor does not rotate correctly (the motor is overloaded). Poor contact in the deck conveying motor/desk drive motor connector terminals.
Remedy: Replace the deck conveying motor board/ desk drive motor board and check for correct operation. Check the gears and remedy if necessary. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.

Code: 4000

Description: Polygon motor synchronization problem
• The polygon motor does not reach the stable speed within 15 s of the polygon motor remote signal turning on.
Causes: Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective power supply unit. Defective engine controller PWB.
Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU (see page 1-6-11). Check if 24 V DC is supplied to CN2-1 on the engine controller PWB. If not, replace the power supply unit. Check if 24 V DC is output from CN8-10 on the engine controller PWB. If not, replace the engine controller PWB.

Code: 4010

Description: Polygon motor steady-state problem
• The polygon motor rotation is not stable for 600 ms after the polygon motor rotation has been stabilized.
Causes: Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective power supply unit. Defective engine controller PWB.
Remedy: Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU (see page 1-6-11). Check if 24 V DC is supplied to CN2-1 on the engine controller PWB. If not, replace the power supply unit. Check if 24 V DC is output from CN8-10 on the engine controller PWB. If not, replace the engine controller PWB.

Code: 4200

Description: BD steady-state problem
• The VTC detects a BD error for 600 ms after the polygon motor rotation has been stabilized.
Causes: Defective laser diode. Defective polygon motor. Defective engine controller PWB.
Remedy: Replace the LSU (see page 1-6-11). Replace the LSU (see page 1-6-11). Replace the engine controller PWB and check for correct operation.

Code: 5300

Description: Broken cleaning lamp wire
While the cleaning lamp is on, the broken cleaning lamp wire detection signal is detected for 2 s continuously.
Causes: Defective cleaning lamp. Defective engine controller PWB.
Remedy: Replace the cleaning lamp. Replace the engine controller PWB and check for correct operation.

Code: 6000

Description: Broken fuser heater wire
• The fuser temperature does not increase for 40 s after the fuser heaters have been turned on for warming up. • The fuser temperature remains below 50 °C/122 °F for 10 s continuously after the fuser heaters have been turned on during stabilization.
Causes: Poor contact in the fuser unit thermistor connector terminals. Fuser unit thermistor installed incorrectly. Fuser unit thermostat triggered. Fuser unit heater M or S installed incorrectly.
Remedy: Check the connection of connector CN10 on the engine controller PWB and the continuity across the connector terminals. Repair or replace if necessary. Check and reinstall if necessary. Check for continuity. If none, replace the fuser unit thermostat. Check and reinstall if necessary. Check for continuity. If none, replace the fuser unit heater M or S (see page 1-6-20).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie