• Code: E130
• Description: 1st drawer misfeeding (Paper not reaching the 1st drawer feed sensor): The paper fed from the 1st drawer does not reach the 1st drawer feed sensor.
• Remedy: 1. Open the jam access cover and check if there is any paper in front of the 1st drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 1st drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[G]) * If it is working properly, proceed to 9. If not, check 3 to 8 below. 3. Check if the connector CN513 on the PFC board is disconnected from the 1st drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 1st drawer feed sensor. 5. Replace the PFC board. 6. Is the feed motor working? (Perform the output check: 03-120) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN512 on the PFC board is disconnected from the feed motor or the harnesses are open circuited. Correct if any. 8. Replace the feed motor. 9. Replace the PFC board. 10.Check the 1st drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E140
• Description: 2nd drawer misfeeding (Paper not reaching the 2nd drawer feed sensor): The paper fed from the 2nd drawer does not reach the 2nd drawer feed sensor.
• Remedy: 1. Open the paper feed cover and check if there is any paper in front of the 2nd drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 2nd drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[F]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN512 on the PFC board is disconnected from the 2nd drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 2nd drawer feed sensor. 5. Replace the PFC board. 6. Is the feed motor working? (Perform the output check: 03-121) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN512 on the PFC board is disconnected from the feed motor or the harnesses are open circuited. Correct if any. 8. Replace the feed motor. 9. Replace the PFC board. 10.Check the 2nd drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E150
• Description: 3rd drawer misfeeding (Paper not reaching the 3rd drawer feed sensor): The paper fed from the 3rd drawer does not reach the 3rd drawer feed sensor
• Remedy: 1. Open the paper feed cover and check if there is any paper in front of the 3rd drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 3rd drawer feed sensor working? (Perform the input check: 03-[FAX]OFF/[2]/[D]) * If it is working properly, proceed to 7. If not, check 3 to 6 below. 3. Check if the connector CN505 on the PFC board is disconnected from the 3rd drawer feed sensor or the harnesses is open circuited. Check if the connector CN505 on the PFC board is disconnected. Correct if any. 4. Replace the 3rd drawer feed sensor. 5. Replace the PFC board. 6. Is the feed/transfer motor working? (Perform the output check: 03-226) * If it is working properly, proceed to 12. If not, check 8 to 11 below. 7. Check if the connectors CN502 on the LGC board is disconnected from the feed/transfer motor or the harnesses are open circuited. Check if the connector CN502 on the PFC board is disconnected. Correct if any. 8. Replace the feed/transfer motor. 9. Replace the PFC board. 10.Check the 3rd drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E160
• Description: 4th drawer misfeeding (Paper not reaching the 4th drawer feed sensor): The paper fed from the 4th drawer does not reach the 4th drawer feed sensor.
• Remedy: 1. Open paper feed cover and check if there is any paper in front of the 4th drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 4th drawer feed sensor working? (Perform the input check: 03-[FAX]OFF/[8]/[D]) * If it is working properly, proceed to 7. If not, check 3 to 6 below. 3. Check if the connectors CN502 on the PFC board is disconnected from the 4th drawer feed sensor or the harnesses are open circuited. Check if the connector CN502 on the PFC board is disconnected. Correct if any. 4. Replace the 4th drawer feed sensor. 5. Replace the PFC board. 6. Is the 4th drawer feed clutch working? (Perform the output check: 03-122) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connectors CN507 on the PFC board is disconnected from the 4th drawer feed clutch or the harnesses are open circuited. Check if the connectors CN502 on the PFP board is disconnected. Correct if any. 8. Replace the 4th drawer feed clutch. 9. Replace the PFC board. 10.Check the 4th drawer feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E180
• Description: Option LCF misfeeding (Paper not reaching the LCF feed sensor): Paper fed from the LCF does not reach the LCF feed sensor.
• Remedy: 1. Is the LCF feed sensor working? (Perform the input check: 03-[SCAN]ON/[5]/[E]). * If it is working properly, proceed to 7. If not, check 2 to 6 below. 2. Check if the connector CN503 on the PFC board is disconnected from the LCF feed sensor or the harnesses are open circuited. Correct if so. 3. Check if the LCF feed sensor is correctly installed or the actuator is properly moved. 4. Replace the LCF feed sensor. 5. Replace the LCF board. 6. Replace the PFC board. 7. Is the LCF transport motor working? (Perform the output check: 03-127.) * IIf it is working properly, proceed to 11. If not, check 8 to 10 below. 8. Check if the connector CN503 on the PFC board is disconnected from the LCF transport motor or the harnesses are open circuited. Correct if so (including J854 and J850 on the LCF board). 9. Replace the LCF transport motor. 10.Replace the PFC board. 11.Check if there is any abnormality on the driving section of the LCF transport motor the roller. Correct if any.

• Code: E190
• Description: LCF misfeeding (Paper not reaching the LCF feed sensor): The paper fed from the LCF does not reach the LCF feed sensor.
• Remedy: 1. Open the LCF side cover and check if there is any paper in front of the LCF feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the LCF feed sensor working? (Perform the input check: 03-[FAX]OFF/[0]/[G]) * If it is working properly, proceed to 7. If not, check 3 to 6 below. 3. Check if the connectors CN349 on the LGC board is disconnected from the LCF feed sensor or the harnesses are open circuited. Check if the connectors CN1 and CN6 on the LCF board are disconnected. Correct if any. 4. Replace the LCF feed sensor. 5. Replace the LGC board. 6. Is the LCF feed clutch working? (Perform the output check: 03-209) * If it is working properly, proceed to 12. If not, check 8 to 11 below. 7. Check if the connectors CN349 on the LGC board is disconnected from the LCF feed clutch or the harnesses are open circuited. Check if the connectors CN1 and CN5 on the LCF board are disconnected. Correct if any. 8. Replace the LCF feed clutch. 9. Replace the LGC board. 10.Check the LCF feed roller, separation roller and pickup roller. Replace them if they are worn out.

• Code: E200
• Description: 1st drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
• Remedy: 1. Open the jam access cover and check if there is any paper in front of the 1st drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 1st drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[G]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN516 on the PFC board is disconnected from the 1st drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 1st drawer feed sensor. 5. Replace the PFC board. 6. Is the transport motor-1 working? (Perform the output check: 03-124 or 524) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN512 on the PFC board is disconnected from the transport motor-1 or the harnesses are open circuited. Correct if any. 8. Replace the transport motor-1. 9. Replace the PFC board. 10.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 11.Check the transport roller. Replace it if it is worn out.

• Code: E210
• Description: 2nd drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the 1st drawer feed sensor.
• Remedy: 1. Open the jam access cover and check if there is any paper in front of the 1st drawer feed sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the 1st drawer feed sensor working? (Perform the input check: 03-[FAX]ON/[1]/[G]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN516 on the PFC board is disconnected from the 1st drawer feed sensor or the harnesses are open circuited. Correct if any. 4. Replace the 1st drawer feed sensor. 5. Replace the PFC board. 6. Is the transport motor-1 working? (Perform the output check: 03-124 or 524) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN512 on the PFC board is disconnected from the transport motor-1 or the harnesses are open circuited. Correct if any. 8. Replace the transport motor-1. 9. Replace the PFC board. 10.Check the condition of the feed roller, separation roller and pickup roller of each paper source, and replace them if they are worn out. 11.Check the transport roller. Replace it if it is worn out.