• Code: E074
• Description: 4th drawer media type mis-setting jam: The media type setting of the 4th drawer is incorrect.
• Remedy: Remove any paper which has jammed due to media type mis-setting and then confirm and set the following: * When this jam occurred during fax data printing, the user must place paper of the same media type as that of the set paper. If the user does not have this media type, the media type setting must be changed by means of the following codes. 08-9300: 1st drawer media type setting (*1) 08-9301: 2nd drawer media type setting (*1) 08-9302: 3rd drawer media type setting (*1) 08-9303: 4th drawer media type setting (*1) 08-9304: Tandem LCF media type setting (*1) 08-9347: Option LCF media type setting (*1) (*1) 0: Plain paper, 1: Thick paper 1, 2: Thick paper 2, 3: Thick paper 3, 8: Recycled paper, 9: Plain paper 1, 10: Plain paper 2 Cases media type setting change (08 code) is required • When a drawer is set for fax data printing but the user does not have the media type set for the fax drawer • When no drawer is set for fax data printing but the user does not have any media type set for each drawer If the media type is correctly set but this error occurs frequently, this media type may be the one which cannot be distinguished easily. In this case change the code below to disable the media type setting checking function. 08-4598 0: Enabled 1: Disabled

• Code: E075
• Description: Option LCF media type mis-setting jam: The media type setting of the option LCF is incorrect.
• Remedy: Remove any paper which has jammed due to media type mis-setting and then confirm and set the following: * When this jam occurred during fax data printing, the user must place paper of the same media type as that of the set paper. If the user does not have this media type, the media type setting must be changed by means of the following codes. 08-9300: 1st drawer media type setting (*1) 08-9301: 2nd drawer media type setting (*1) 08-9302: 3rd drawer media type setting (*1) 08-9303: 4th drawer media type setting (*1) 08-9304: Tandem LCF media type setting (*1) 08-9347: Option LCF media type setting (*1) (*1) 0: Plain paper, 1: Thick paper 1, 2: Thick paper 2, 3: Thick paper 3, 8: Recycled paper, 9: Plain paper 1, 10: Plain paper 2 Cases media type setting change (08 code) is required • When a drawer is set for fax data printing but the user does not have the media type set for the fax drawer • When no drawer is set for fax data printing but the user does not have any media type set for each drawer If the media type is correctly set but this error occurs frequently, this media type may be the one which cannot be distinguished easily. In this case change the code below to disable the media type setting checking function. 08-4598 0: Enabled 1: Disabled

• Code: E076
• Description: Tandem LCF media type mis-setting jam: The media type setting of the tandem LCF is incorrect.
• Remedy: Remove any paper which has jammed due to media type mis-setting and then confirm and set the following: * When this jam occurred during fax data printing, the user must place paper of the same media type as that of the set paper. If the user does not have this media type, the media type setting must be changed by means of the following codes. 08-9300: 1st drawer media type setting (*1) 08-9301: 2nd drawer media type setting (*1) 08-9302: 3rd drawer media type setting (*1) 08-9303: 4th drawer media type setting (*1) 08-9304: Tandem LCF media type setting (*1) 08-9347: Option LCF media type setting (*1) (*1) 0: Plain paper, 1: Thick paper 1, 2: Thick paper 2, 3: Thick paper 3, 8: Recycled paper, 9: Plain paper 1, 10: Plain paper 2 Cases media type setting change (08 code) is required • When a drawer is set for fax data printing but the user does not have the media type set for the fax drawer • When no drawer is set for fax data printing but the user does not have any media type set for each drawer If the media type is correctly set but this error occurs frequently, this media type may be the one which cannot be distinguished easily. In this case change the code below to disable the media type setting checking function. 08-4598 0: Enabled 1: Disabled

• Code: E090
• Description: Image data delay jam: Image data to be printed cannot be prepared.
• Remedy: 1. Remove the paper remained in front of the registration sensor. 2. Check if the error is cleared by turning the power OFF and then back ON. 3. Check if the connectors connecting the SYS board, IMG board and LGC board are disconnected. 4. Check if the connectors connecting the IMG board and SLG board are disconnected. 5. Check if the connectors of the HDD are disconnected. 6. Check if the page memory is correctly connected to the connecter on the SYS board. 7. Replace the page memory. 8. Replace the HDD, SYS board, IMG board and LGC board.

• Code: E091
• Description: Motor-ON time-out jam: The equipment does not operate normally because abnormality occurred on an interface between the SYS board and engine firmware.
• Remedy: 1. Check if there is any paper in the equipment. Remove it if there is. 2. Check if the error is cleared by turning the power OFF and then back ON. 3. Check if the connectors connecting the SYS board, IMG board and LGC board are disconnected. 4. Check if the connectors connecting the IMG board and SLG board are disconnected. 5. Check if the connectors of the HDD are disconnected. 6. Replace the HDD, SYS board, IMG board and LGC board.

• Code: E0A0
• Description: Image transport ready time-out jam: Image data to be printed cannot be sent.
• Remedy: 1. Remove the paper remained in front of the registration sensor. 2. Check if the error is cleared by turning the power OFF and then back ON. 3. Check if the connectors on the LGC board are disconnected. 4. Replace the LGC board.

• Code: E110
• Description: ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing.
• Remedy: 1. Open the jam access cover and check if there is any paper in front of the registration sensor. Remove it if there is. * If the error still occurs, check the following. 2. Is the registration sensor working? (Perform the input check:03-[FAX]OFF/[7]/[F]) * If it is working properly, proceed to 6. If not, check 3 to 5 below. 3. Check if the connector CN337 on the LGC board is disconnected from the registration sensor or the harnesses are open circuited. Correct if any. 4. Replace the registration sensor. 5. Replace the LGC board. 6. Is the ADU clutch working? (Perform the output check: 03-222) * If it is working properly, proceed to 10. If not, check 7 to 9 below. 7. Check if the connector CN338 on the LGC board is disconnected from the ADU clutch or the harnesses are open circuited. Correct if any. 8. Replace the ADU clutch. 9. Replace the LGC board. 10.Check the rollers in the ADU. Replace them if they are worn out.

• Code: E120
• Description: Bypass misfeeding (Paper not reaching the bypass feed sensor): Paper fed from the bypass tray does not reach the bypass feed sensor.
• Remedy: 1. Are the bypass motor, bypass pick-up solenoid and bypass feed sensor working? (Perform the output check: 03-126, 03-254 and the input check: 03-[FAX]ON/[4]/[D]) * If it is working properly, proceed to 6. If not, check 2 to 5 below. 2. Check if the connector CN469, CN497, CN498 on the ADU board is disconnected from the bypass motor or the bypass feed sensor, or the harnesses are open circuited. Correct if any. 3. Replace the bypass motor. 4. Replace the bypass pick-up solenoid. 5. Replace the bypass feed sensor. 6. Replace the LGC board. 7. Check the rollers in the ADU. Replace them if they are worn out.