Remedy: 1 • Paper size sensors 1 and 2 • Residual paper sensors 1—4 • Paper level sensor • Lower limit switch • Docking switch • Upper limit • Paper sensor switch • Paper feed sensor Go to “Sensor/Sw Test”, and perform the LED sensor test. You can block each sensor to verify if it is working properly. Replace the failing sensor. 2 • Tray motor • Paper feed motor • HCPF power supply • Pickup solenoid • Paper feed roller • Transfer roller • Paper feed clutch • Tray drive belt Be sure that all rollers, gears, and belts are in good working order. Replace as necessary. 3 • Paper feed clutch • Pickup solenoid • HCF power supply • Paper feed motor • Tray motor • HCPF board Go to “Maintenance Mode”, and run the tests.
Remedy: 1 Is connector J5 on the RIP board connected properly? Go to step 2. Properly connect J5. 2 Is 24 V dc present between pins 1 and 3 of connector J5 on the RIP board? Replace the RIP fan. Go to step 3. 3 Is 24 V dc present between pin 80 of the RIP/printer controller and ground? Replace the RIP board. Replace the printer controller board.
Remedy: 1 Are CN14 on the printer controller board and CN03 on the printhead controller board properly connected? Go to step 2. Connect CN14 and CN03. 2 Is +24V present between pins and 1 and 3 on connectors CN12 (upper left fan) and CN11 (upper right fan) on the printer controller board? Replace the failing fan. Replace the printer controller board.
Remedy: 1 Is CN17 on the printer controller board properly connected? Go to step 2. Connect CN17. 2 Is CN6 on the CK2 daughter board properly connected? Go to step 3. Connect CN6. 3 Is +24 V present between pins 1 and 3 of connector CN6 on the CK2 daughter board? Replace the power supply fan. Replace the printer controller board. 4 Did either exchange solve the problem? Problem solved. Replace the CK2 daughter board.
Remedy: 1 Replace the fuser. Did this fix the problem? Problem solved. Return the fuser, replace the power supply 2, and go to step 2. 2 Did replacing power supply 2 fix the problem? Problem solved. Return power supply 2, and replace the printer controller board
Remedy: 1 Is connector CN19 on the printer controller board connected properly? Disconnect CN19 and turn the printer on. Go to step 2. Plug the connector in securely. 2 Is error 923 displayed? Power off, and reconnect CN19. Go to step 3. Replace the printer controller board. 3 Power the printer off and short-circuit pins (1 and 2) and (3 and 4) of CN19 and power on. Is error 923 displayed? Replace the fuser. Replace the printer controller board.
Remedy: 1 Turn off the printer and reinstall the fuser, making sure it clicks into place. Turn on the printer. Did this resolve the problem? Problem solved. Go to step 2. 2 Is connector CN19 on the printer controller board connected properly? Disconnect CN19, and turn the printer on. Go to step 3. Plug the connector in securely. 3 Is error 924 displayed? Turn the printer off, and reconnect CN19. Go to step 4. Replace the printer controller board. 4 Turn off the printer and short-circuit pins 8 and 9 of CN19. Turn on the printer. Is error 924 displayed? Replace the fuser. Replace the printer controller board.
Remedy: 1 Has the high voltage power board (HVU) been removed/replaced? Inspect the secondary card on the high voltage board (HVU) for a broken component (Q906). Replace the high voltage board (HVU) if necessary. Go to step 2. 2 Is connector CN9 on the printer controller board connected properly? Replace the printer controller board. Go to step 3. Plug the connector in securely. 3 Did replacing the printer controller board fix the problem? Problem solved. Replace the high voltage power board (HVU).
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.