Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Lexmark C920dtn — Trang 12/13

Code: 981

Description: Belt Up/Down Sensor Error 981 Service Switch Error
Remedy: 1 Is the engine code the latest level? Go to step 2. Update the printer with latest code level. If this does not resolve the problem, continue with step 2. 2 Are connectors CN409 and CN407 on the sensor board connected properly? Go to step 3. Plug the connectors in securely. 3 Are connectors CN11 on the CK1 daughter board, and CN15, CN3, CN4, and CN5 on the printer controller board connected properly? Go to step 4. Properly connect all connections. 4 Remove the transfer belt. Verify the belt up/down sensor actuator flag, on the bottom of the transfer belt unit is properly installed, not broken, and in the proper position. Rotate the shaft attached to the belt up/down sensor actuator flag. Are there any binds other than when engaging the transfer belt? Make sure the sensor is fully snapped in place, and that the sensor connector is fully seated. Are these items correct? Go to step 5. If the sensor is out of position or disconnected, properly install the sensor and properly connect the sensor to the belt unit. If the shaft attached to the belt up/down sensor actuator binds, replace the transfer belt unit. If the sensor actuator flag is broken, replace the transfer belt unit. 5 Clean the belt up/down sensor (located on the bottom of the transfer belt unit). Does this fix the problem? Problem solved. Go to step 6. 6 Disconnect the belt up/down sensor on the transfer belt unit, bypassing the density sensor and door open sensor. Power on the printer. Does the belt up/down shaft rotate during POST? Replace the transfer belt unit. Go to step 7. 7 Replace the transfer belt unit. Did this fix the problem? Problem solved. Replace the printer controller board.

Code: 982

Description: Sensor Controller Error
Remedy: 1 Turn the printer off, and wait 30 seconds. Turn the printer on. Is error 982 displayed? Replace the printer controller board. Problem solved.

Code: 983

Description: Black Gear Sensor Error
Remedy: 1 Is connector CN20 on the printer controller board connected properly? Go to step 2. Plug the connector in securely. 2 Check the cable running to CN20 for damage. Is the cable damaged? Replace the cable. Go to step 3. 3 Clean the gear sensor. Does this correct the problem? Problem solved. Go to step 4. 4 Replace the sensor card. Did this resolve the problem? Problem solved. Replace the drive unit.

Code: 984

Description: Yellow Gear Sensor Error
Remedy: 1 Is connector CN20 on the printer controller board connected properly? Go to step 2. Plug the connector in securely. 2 Check the cable running to CN20 for damage. Is the cable damaged? Replace the cable. Go to step 3. 3 Clean the gear sensor. Does this correct the problem? Problem solved. Go to step 4. 4 Replace the sensor card. Did this resolve the problem? Problem solved. Replace the drive unit.

Code: 985

Description: Transfer Belt Thermistor Error
Remedy: 1 Are connectors CN407 and CN411 on the sensor board connected properly? Go to step 2. Plug the connector in securely. 2 Is connector CN15 on the printer controller board connected properly? Replace the transfer belt unit. If the problem remains, replace the printer controller board. Plug the connector in securely.

Code: 986

Description: Transparency (OHP) Sensor Error
Remedy: 1 Are connectors CN4 (light emitting) and CN5 (light receiving) on the CK1 daughter board connected properly? Go to step 2. Plug the connector in securely. 2 Test the sensor. While actuating the sensor, does the voltage fluctuate between 0 V and +5 between pins 2 and 3 of connector CN7 of the printer controller board? Replace the printer controller board. Replace the MPF unit.

Code: 987

Description: Service Toner Cartridge
Remedy: 1 Turn the printer off and then back on. Did this fix the error? Problem solved. Go to step 2. 2 Try different toner cartridges. Did this fix the error? Problem solved. Go to step 3. 3 Check the cable connections on the RFID antenna, and CN 21 on the printer controller card. Are they properly connected? Go to step 4. Properly connect the connections. 4 Check the RFID cable. Is it damaged? Replace the RFID cable. Replace the printer controller board.

Code: 991

Description: Service Paper Option
Remedy: 1 POR the printer. Does the error return? Go to step 2. Problem solved. 2 Check connections CN3,4,5,17,18 on the printer controller board. Are they properly connected? Go to step 3. Properly connect the connectors. 3 Are the size sensing levers bent or damaged? Replace the size sensing levers. Go to step 4. 4 Replace the CK 2 daughter board. Did this solve the problem? Problem solved. Go to step 5. 5 Are any actuators on the paper-feed unit damaged? Replace the paper-feed unit. Replace the printer controller board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie