Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi OKI C9600 — Trang 9/15

Code: 230

Display: Service Call 230: Error
Description: RFID Reader not Installed
Remedy: 1) RFID read device error 2) Does the Error take place again?
Check the connection of the RFID R/W board. Replace the RFID R/W board. Replace the S2V board.

Code: 231

Display: Service Call 231: Error
Description: RFID Reader I/F Error
An interface error was detected with the RFID reader device.
01: communication error between the RFID reader and the engine PCB. 02: the transceiver circuit error of the RFID reader. 03: communication error between the RFID reader and the Tag chip. 04: the RFID Tag detection error (more than 4 chips).
Remedy: 01: Same action as for error 230 02: Replace the RFID R/W board. 03: Check the connection of the antenna cable. 04: Check to confirm that the number of RFID tags is correct.

Code: 240 ... 245, 247, 248

Display: Service Call 240: Error to 245: Error 247: Error 248: Error
Description: Engine Program Memory Error
240: Flash-memory hardware error 241: Duplex flash-memory error 242: Optional tray-2 flash-memory error 243: Optional tray-3 flash-memory error 244: Optional tray-4 flash-memory error 245: Optional tray-5 flash-memory error 247: Sub-CPU flash-memory error 248: Inverter flash-memory error
Remedy: If the error still occurs after rebooting, replace the circuit board of the relevant unit.

Code: 310

Display: Close the Cover 310: Top Cover Open
Description: The printer engine cover is open.
Remedy: 1) Check to see if the top cover is open. 2) Check to see if the cover switch is normal.
Close top cover Replace the cover switch.

Code: 320

Display: Reset fuser 320: Fuser Error
Description: After turning ON the power or when cover is closed, the sensor detects that the unit is missing.
Remedy: 1) Is an Error message displayed? 2) Is the fuser unit mounted properly? 3) Does the Error take place again?
Check how the fuser is mounted. Re-mount the fuser, then turn ON the power again. Replace the Fuser Unit Assy

Code: 321

Display: Turn OFF the power and wait for awhile. 321: MOTOR OVERHEAT
Description: This indicates that the motor has overheated and that the printer is temporarily unusable.
Remedy: Wait a while then turn ON power again.

Code: 323

Display: Open Cover 323: Paper Thickness Error
Description: When media is missing, the sensor output value is outside the standard value. (Only for Factory Mode)
Remedy: 1) Has any abnormal substance get mixed in with the sensor? 2) Can the paper thickness detection be reset and restored by opening/closing the tray? 3) Is operation restored by turning OFF/ON the power?
Remove obstruction/impurity. Normal

Code: 324

Display: Open Cover 324: Paper Thickness Error
Description: Sensor Output Difference Value Outside Standard (Only for Factory Mode)
Remedy: 1) Has any abnormal substance get mixed in with the sensor? 2) Can the paper thickness detection be reset and restored by opening/closing the tray? 3) Is operation restored by turning OFF/ON the power?
Remove obstruction/impurity. Normal
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie