Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi OKI CX1145MFP — Trang 9/14

Code: CC61

Description: Punch motor (M3) home position detion error
Remedy: MJ-1101 (When MJ-6101 is installed) Is there any paper remaining on the transport path? → →YES Remove the paper. NO Rotate the punch motor (M3). Does it rotate smoothly? → →NO Fix the mechanism. YES Are the punch home position sensor (S4) and its wiring correct? → →NO Replace the sensor. Correct the wiring. YES Is the wiring between the hole punch control PC board (HP) and punch motor (M3) correct? → →NO Correct the wiring. YES 1) Replace the punch motor (M3). 2) Replace the hole punch control PC board (HP).

Code: CC71

Description: Punch ROM checksum error
Remedy: MJ-1101 (When MJ-6101 is installed) Is the conductor pattern on the hole punch control PC board (HP) open circuited or short circuited? → →YES Replace the hole punch control PC board (HP). NO Replace the finisher control PC board.

Code: CC72

Description: Punch RAM read/write error
Remedy: MJ-1101 (When MJ-6101 is installed) Is the conductor pattern on the hole punch control PC board (HP) open circuited or short circuited? → →YES Replace the hole punch control PC board (HP). NO Replace the finisher control PC board.

Code: CC80

Description: Front jogging motor abnormality/Front aligning plate motor abnormality
Remedy: MJ-1022 (Front jogging motor abnormality) Is the front jogging plate home position sensor (S6) working properly? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and front jogging motor (M3) correct? → NO → Correct the wiring. YES Has the rack run over the stopper of the roll? → YES → Fix it. NO 1) Replace the front jogging motor. 2) Replace the finisher controller PC board.
MJ-1023/1024 (Front aligning plate motor abnormality) Is the front aligning plate home position sensor (PI36) normal? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and the front aligning plate motor (M33) correct? → NO → Correct the wiring. YES Is there any mechanical problem with the path of aligning plate? → NO → Fix the mechanism. YES 1) Replace the front aligning plate motor. 2) Replace the finisher controller PC board.

Code: CC80

Description: Rear alignment motor abnormality
Remedy: MJ-1101 Is there any mechanical problem when the rear alignment plate is moved? → →YES Fix the mechanism. NO Is the harness between the rear alignment motor (M10) and the finisher control PC board (CN10) disconnected or open circuited? l → →YES • Reconnect the connector securely. • Replace the harness. NO 1) Replace the rear alignment motor (M10). 2) Replace the finisher control PC board.

Code: CC90

Description: Upper stack tray lift motor abnormality
Remedy: MJ-1022 Is the wiring between the finisher controller PC board and upper stack tray lift motor (M5) correct? → NO → Correct the wiring. YES Are the front and rear sides of the upper stack tray leveled? → NO → Level them. YES Is the upper stack tray lift motor clock sensor (S19) working properly? → NO → Level them. YES Is the stack tray paper height sensor (S10) working properly? → NO → Replace the sensor. YES Are the upper stack tray upper limit sensor (S25), upper stack tray full sensor (S23) and stack processing safety switch (S26) working properly? → NO → Replace the sensor or sensor controller PC board. YES Does the voltage between the pins J14-1 and -2 on the finisher controller PC board become 24V when the upper stack tray lift motor starts rotating? → NO → Replace the finisher controller PC board. YES Check the wiring between the upper stack tray lift motor and finisher controller PC board. If there is no problem, replace the upper stack tray lift motor.

Code: CCA0

Description: Lower stack tray lift motor abnormality
Remedy: MJ-1022 Is the wiring between the finisher controller PC board and lower stack tray lift motor (M7) correct? → NO → Correct the wiring. YES Are the front and rear sides of the lower stack tray leveled? → NO → Level them. YES Is the lower stack tray lift motor clock sensor (S9) working properly? → NO → Replace the sensor. YES Is the stack tray paper height sensor (S10) working properly? → NO → Replace the sensor. YES Are the lower stack tray upper limit sensor (S13) and lower stack tray full sensor (S23) working properly? → NO → Replace the sensor or sensor controller PC board. YES Does the voltage between the pins J3-1 and -2 on the finisher controller PC board become 24V when the lower stack tray lift motor starts rotating? → NO → Replace the finisher controller PC board. YES Check the wiring between the upper stack tray lift motor and finisher controller PC board. If there is no problem, replace the motor.

Code: CCB0

Description: Rear jogging motor abnormality
Remedy: MJ-1022 Is the rear jogging plate home position sensor (S7) working properly? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and rear jogging motor (M4) correct? → NO → Correct the wiring. YES Has the rack run over the stopper of the roll? → YES→ Fix it. NO 1) Replace the rear jogging motor. 2) Replace the finisher controller PC board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie