Remedy: MJ-1101 Is the harness between the stapler and the finisher control PC board (CN2) disconnected or open circuited? l → →YES • Reconnect the connector securely. • Replace the harness. NO Are the harnesses in the stapler disconnected or open circuited? l → →YES • Reconnect the connector securely. • Replace the harness. NO Replace the finisher control PC board.
Remedy: MJ-1101 Is there any mechanical problem when the stapler is moved? → →YES Fix the mechanism. NO Is there a disconnection of the connector, incorrect installation or breakage of the stapler unit home position sensor (S10)? ll → →YES • Connect the connector securely. • Reinstall the sensor correctly. • Replace the sensor. NO Is the harness between the stapler unit home position sensor (S10) and the finisher control PC board (CN1) disconnected or open circuited? l → →YES • Reconnect the connector securely. • Replace the harness. NO Is the harness between the stapler unit shift motor (M4) and the finisher control PC board (CN5) disconnected or open circuited? l → →YES • Reconnect the connector securely. • Replace the harness. NO Replace the finisher control PC board.
Remedy: MJ-1023/1024 Is the stapler shift home position sensor (PI40) working normally? → NO → Replace the sensor. YES Is the wiring between the finisher controller PC board and the stapler shift motor (M35) correct? → NO → Correct the wiring. YES Is there any mechanical problem with the stapler stand motion path? → YES→ Fix the lift mechanism. NO 1) Replace the stapler shift motor. 2) Replace the finisher controller PC board. MJ-1101 Is there any mechanical problem when the stapler is moved? → →YES Fix the mechanism. NO Is the harness between the stapler unit shift motor (M4) and the finisher control PC board (CN5) disconnected or open circuited? l → →YES • Reconnect the connector securely. • Replace the harness. NO 1) Replace the stapler unit shift motor (M4). 2) Replace the finisher control PC board.
Remedy: MJ-1023/1024 Is the problem solved by turning the power of the equipment OFF and ON? → YES→ End. NO 1) Replace the finisher controller PC board. 2) Replace the punch controller PC board.
Remedy: MJ-1101 Is the error recovered when the power of the equipment is turned OFF and then back ON? → →YES End. NO Replace the finisher control PC board.
Remedy: MJ-1101 Is the error recovered when the power of the equipment is turned OFF and then back ON? → →YES End. NO 1) Check if the conductor pattern on the finisher controller PC board is open circuited or short circuited. 2) Replace the finisher control PC board.
Description: Paper pushing plate motor abnormality
Remedy: MJ-1024 Are the paper pushing plate home position sensor (PI14), paper pushing plate top position sensor (PI15) and paper pushing plate motor clock sensor (PI1) working normally? → NO → Replace the sensor. YES Is the paper pushing plate drive mechanism normal? → NO → Fix the mechanism. YES 1) Replace the paper pushing plate motor (M8). 2) Replace the saddle stitcher controller PC board.
Description: [CBA0] Stitch motor (front) abnormality [CBB0] Stitch motor (rear) abnormality
Remedy: MJ-1024 Are the front and rear stitchers and their stands installed properly? → NO → Install them properly. YES Are the stitcher home position switches (SW7/SW5) and stitcher motors (M7/M6) on the front and rear stitchers working normally? → NO → Replace the front or rear stitcher. YES Replace the saddle stitcher controller PC board.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.