Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MP3353 — Trang 6/30

Code: SC542-03

Description: Fusing central thermopile does not reload • Time out (Non-rotating roller): Reload temperature not reached in 28 seconds after the fusing lamp control start • Time out (Rotating roller): Reload temperature not reached in 46 seconds after the fusing lamp control start
Causes: • Disconnection of the fusing lamp • After excessive temperature rise prevention unit operation
Remedy: • Check the fusing thermistor is set correctly. • Replace the fusing thermistor. • Check that the input voltage is within acceptable limits. • Replace the fusing unit. • Repace the BCU. • Replace the fusing lamp in the case of disconnection.

Code: SC543

Description: Fusing overheat error 1 (center) The fusing thermistor detected a fusing temperature over 230°C for 1 sec. at the center of the hot roller.
Causes: • TRIAC short on PSU (PSU defective) • BCU defective • Power supply voltage unstable
Remedy: • Replace the PSU. • Replace the BCU. • Replace the fusing unit.

Code: SC544

Description: Fusing overheat error 2 (center) A fusing temperature over 250°C is detected at the center of the hot roller by the fusing temperature monitor circuit in the BCU board. The power was interrupted for more than 0.3 sec.
Causes: • TRIAC short on PSU (PSU defective) • BCU defective • Fusing thermistor defective • Power supply voltage unstable
Remedy: • Replace the PSU. • Replace the BCU. • Replace the fusing unit.

Code: SC545

Description: Fusing overheat error 3 (center) After warmup, the center of the hot roller attained full operating temperature and maintained this temperature for 29 sec. without the hot roller rotating.
Causes: • Center hot roller thermistor installed incorrectly, disconnected. • Center hot roller thermistor defective
Remedy: • Check the hot roller thermistor is set correctly. • Replace the hot roller thermistor. • Replace the BCU. • Check that the input voltage is within acceptable limits. • Replace the fusing unit. • Replace the fusing lamp in the case of disconnection.

Code: SC547-01

Description: Zero cross error (relay-contact soldering) The zero cross signal is detected for 0.05 seconds three times even though the fusing lamp relay is off when turning on the main power.
Causes: • Fusing relay damage (contact open) • Fusing relay drive circuit fault • PSU fuse (24VS) blowout
Remedy: • Turn the main power supply switch OFF/ON. • If the fusing relay is damaged, replace the PSU. • Check the connection between PSU and control board, and replace harness and board if necessary. • If the PSU fuse (24VS) blows out, replace the PSU.

Code: SC547-02

Description: Zero cross error (relay contact fault) The zero cross signal is not detected for 3 seconds even though the fusing lamp relay is on after turning on the main power or closing the front door.
Causes: • Fusing relay damage (contact open) • Fusing relay drive circuit fault • PSU fuse (24VS) blowout
Remedy: • Turn the main power supply switch OFF/ON. • If the fusing relay is damaged, replace the PSU. • Check the connection between PSU and control board, and replace harness and board if necessary. • If the PSU fuse (24VS) blows out, replace the PSU.

Code: SC547-03

Description: Zero cross error (low-frequency error) • In the event of an error
Causes: • Fusing relay damage (contact open) • Fusing relay drive circuit fault • PSU fuse (24VS) blowout
Remedy: • Turn the main power supply switch OFF/ON. • If the fusing relay is damaged, replace the PSU. • Check the connection between PSU and control board, and replace harness and board if necessary. • If the PSU fuse (24VS) blows out, replace the PSU.

Code: SC547-04

Description: Zero cross error (input signal error) • In the event of an error
Causes: • Fusing relay damage (contact open) • Fusing relay drive circuit fault • PSU fuse (24VS) blowout
Remedy: • Turn the main power supply switch OFF/ON. • If the fusing relay is damaged, replace the PSU. • Check the connection between PSU and control board, and replace harness and board if necessary. • If the PSU fuse (24VS) blows out, replace the PSU.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie