Description: GAVD communication error The I2C bus device ID is not identified during initialization. A device-status error occurs during I2C bus communication. The I2C bus communication is not established due to an error other than a buffer shortage
Description: Finisher exit guide plate motor error After moving away from the guide plate position sensor, the exit guide is not detected at the home position within the prescribed time. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: Guide plate motor disconnected, defective. Guide plate motor overloaded due to obstruction. Guide plate position sensor disconnected, defective.
Remedy: 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in the guide plate motor mechanism. 3. Replace the guide plate position sensor and/or guide plate motor 4. Replace the finisher main board.
Description: Finisher Tray 1 shift motor error The shift roller HP sensor of the upper tray does not activate within the prescribed time after the shift tray starts to move toward or away from the home position. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: Shift tray HP sensor of the upper tray disconnected, defective. Shift tray motor of the upper tray is disconnected, defective. Shift tray motor of the upper tray overloaded due to obstruction.
Remedy: 1. Check the connections and cables for the components mentioned above. 2. Check for blockages in shift motor mechanism. 3. Replace the shift tray HP sensor and/or shift motor 4. Replace the finisher main board.
Description: Finisher corner stapler motor error The 1st detection failure issues a jam error, and the 2nd failure issues this SC code. For 1000-sheet (booklet) finisher. The stapler motor does not switch off within the prescribed time after operating. The HP sensor of the staple unit does not detect the home position after the staple unit moves to its home position. The HP sensor of the staple unit detects the home position after the staple unit moves from its home position. For 500-sheet finisher. The stapler HP sensor does not detect "ON"/"OFF" signal even the stapler moves from the "OFF"/"ON" position for 0.6 seconds. The stapler HP sensor does not detect "ON" when a stapling job is commanded or the stapler moves.
Causes: Staple jam. Motor overload. Defective stapler motor.
Remedy: 1. Check the connections and cables for the components mentioned above. 2. Replace the HP sensor and/or stapler motor 3. Replace the finisher main board.
Description: Finisher stapler movement motor error For 1000-sheet (booklet) finisher. The stapler HP sensor is not activated within the specified time after the stapler motor turned on. (first detection: jam error, consecutive twice detection SC code). For 500-sheet finisher. The stapler HP sensor does not detect "OFF" signal even the stapler moves from the "ON" position for 0.35 seconds. The stapler HP sensor does not detect "ON" signal even the stapler moves from the "OFF" position for 5.5 seconds.
Causes: Motor overload. Loose connection of the stapler home position sensor. Loose connection of the stapler movement motor. Defective stapler home position sensor. Defective stapler movement motor.
Remedy: 1. Check the connection of the stapler movement motor. 2. Check the connection of the stapler home position sensor. 3. Replace the stapler home position sensor. 4. Replace the stapler movement motor.
Description: 1000-sheet booklet finisher: Stack feed motor error The stack feed HP sensor does not detect "ON" twice (once: jam error) for specified time after the stack feed motor has turned on. The stack feed HP sensor does not detect "OFF" twice (once: jam error) for specified time after the stack feed motor has turned on.
Causes: Motor overload. Loose connection of the stack feed motor. Defective stack feed motor.
Remedy: 1. Check the connections and cables for the stack feed motor and HP sensor. 2. Check for blockages in the stack feed motor mechanism. 3. Replace the stack feed HP sensor and/or stack feed motor 4. Replace the finisher main board.
Description: Finisher punch motor error The punch HP sensor is not activated within the specified time after the punch motor turned on. The 1st detection failure issues a jam error, and the 2nd failure issues this SC code.
Causes: Punch HP sensor disconnected, defective. Punch motor disconnected or defective. Punch motor overload due to obstruction
Remedy: 1. Check the connections and cables for the punch motor and HP sensor. 2. Check for blockages in the punch motor mechanism. 3. Replace the punch HP sensor and/or punch motor 4. Replace the finisher main board.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.