Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC2003 — Trang 13/45

Code: SC511-00

Description: Paper Thickness Sensor Error During initial calibration of the paper thickness sensor, the sensor output value does not become the correct value although 3 or more retries are performed.
Causes: • Paper thickness sensor harness disconnection/connector missing • Dirt on the paper thickness sensor due to paper powder or dust, etc. • Foreign matter adhesion to paper thickness detection unit (1st transport roller)
Remedy:

Code: SC520-01

Description: Registration Motor: Lock During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor • Reset the connector • Replace the harness • Replace the IOB

Code: SC520-02

Description: Paper feed Motor: Lock During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor • Reset the connector • Replace the harness • Replace the IOB

Code: SC520-03

Description: Transport Motor: Lock During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor • Reset the connector • Replace the harness • Replace the IOB

Code: SC521-01

Description: Duplex Entrance Motor: Lock During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor • Reset the connector • Replace the harness • Replace the IOB

Code: SC521-02

Description: Duplex By-pass Motor: Lock During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor • Reset the connector • Replace the harness • Replace the IOB

Code: SC522-00

Description: Paper Exit Motor: Lock During motor ON, after checking the motor error notification registers (err_velo and err_posi) for 500msec, the error state of either register was detected at least 5 times.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective • Encoder defective
Remedy: • Replace the motor • Reset the connector • Replace the harness • Replace the IOB

Code: SC530-00

Description: Fusing Exhaust Heat Fan Lock In the motor ON state, the value of the lock sensor is checked every 100msec. If a lock signal is not obtained for 50 times consecutively.
Causes: • Motor defective • Connector disconnected • Harness broken • IOB defective
Remedy: • Replace the motor • Reset the connector • Replace the harness • Replace the IOB • Replace the fan
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie