Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC2003 — Trang 16/45

Code: SC544-01

Description: Fusing central thermopile high temperature detection (hardware) In the event of an error
Causes: • Triac defective (short-circuit) • Engine controller defective • Heating central thermopile defective • Fusing control software: out of control
Remedy: • If the triac is defective, replace the AC power supply board • If necessary, replace the BCU or the heating central thermopile

Code: SC544-02

Description: Fusing central NC sensor high temperature detection (hardware) In the event of an error
Causes: • Triac defective (short-circuit) • Engine controller defective • Heating central thermopile defective • Fusing control software: out of control
Remedy: • Attach the new fusing unit, then run SP-5-810-002 • If the triac is defective, replace the AC power supply board • If necessary, replace the BCU or the Fusing central NC sensor

Code: SC545-00

Description: Fusing central heater continuously Heat After waiting for full power for more than (t6) seconds continuously, not detected for (t8) seconds. • Definition of heater full power Continuously heating rate set point (maximum heating rate) • Measurement start point After reload (after heater extinguished, after rotation complete) below the standby temperature (target temperature), measurement starts after a heater heat-up request is issued. • Measurement stop condition Rotation started due to a print signal during measurement or other. • Maximum heat-up Duty (SP interlinked value) 0% is excluded.
Causes: • Thermistor deformation/float • Heater disconnection • After excessive temperature rise prevention unit operates
Remedy: • Replace the thermistor • Replace the fusing lamp • Replace the fusing unit

Code: SC547-01

Description: Zero cross error (relay-contact soldering) In the event of an error
Causes: • Fusing relay defective (contact soldering) • Fusing relay drive circuit fault
Remedy: • Turn the main power supply switch OFF/ON • If the fusing relay is damaged, replace the PSU • Check the connection between PSU and control board, and replace harness and board if necessary

Code: SC547-02

Description: Zero cross error (relay contact fault) In the event of an error
Causes: • Fusing relay damage (contact open) • Fusing relay drive circuit fault • PSU fuse (24VS) blowout
Remedy: • Turn the main power supply switch OFF/ON • If the fusing relay is damaged, replace the PSU • Check the connection between PSU and control board, and replace harness and board if necessary • If the PSU fuse (24VS) blows out, replace the fuse

Code: SC547-03

Description: Zero cross error (low-frequency error) In the event of an error
Causes: Frequency instability of commercial power line
Remedy: • Turn the main power supply switch OFF/ON • Check the power source • Check the connection between PSU and control board, and replace harness and board if necessary

Code: SC548-00

Description: Fusing Rotation Detection During heating, there is no input to the edge of the rotation sensor (t7) ms.
Causes: • Motor defective • Sensor defective • Sensor actuator/feeler modification/defective
Remedy: • Replace the motor • Replace the sensor • Replace the actuator/feeler • Replace the fusing unit

Code: SC551-01

Description: Fusing Edge Thermopile Disconnection Below -50 degrees C (or below CB) is detected for (t11) seconds continuously.˜
Causes: • Thermopile disconnection • Connector disconnected
Remedy: • Replace the thermopile • Reset the connector • Replace the connector • Replace the fusing unit
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie