Mã lỗi Ricoh Aficio MPC2010 — Trang 9/18
Code:
Tất cả lỗi (142)
101
120
121
141
142
144
161-001
161-002
165
195
202
203
204
220
222
224
226
230
231
232
233
234
235
236
237
240
241
242
243
285
300
301
302
303
325
360
361
362
363
364
365
366
367
372
373
374
375
380
381
382
383
396
397
400
441
442
443
452
491
492
495
503
504
506
508
530
531
532
533
534
535
540
541
542
543
544
545
547
551
552
553
554
555
557
559
561
563
564
565
571
573
574
610
611
620
632
633
634
635
636
641
650
651
669
670
671
672
681
682
683
687
690
816
817
819
820
821
823
824
826
827
828
829
833
839
851
857
866
867
868
876
878
900
919
920
921
990
991
992
995
997
998
Description: By-pass bottom plate error The signal from the by-pass tray HP sensor does not change for 1.0 second after the by-pass motor has rotated counterclockwise. If this condition occurs three consecutive times, the SC is generated.
Causes: • Disconnect or defective harness of the by-pass motor • Defective or disconnected connection for the by-pass motor. • Defective by-pass motor • Disconnect or defective harness of the by-pass HP sensor • Defective or disconnected connection for the by-pass HP sensor. • Defective by-pass HP sensor
Remedy: Check the operation of the by-pass motor with SP5804-023. No operation: 1. Check the harness connection of the by-pass tray and duplex unit. 2. Replace the by-pass motor. Operation: Check the operation of the by-pass HP sensor with SP5803-048 while the by-pass motor is rotating. No change of Bit 0 1. Check the harness connection of the by-pass HP sensor. 2. Replace the by-pass HP sensor.
Description: Ventilation fan: front error The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected.
Causes: • Defective ventilation fan: front or rear • Disconnected or defective harness • Defective DRB • Defective BCU
Remedy: 1. Check or replace the harness. 2. Replace the ventilation fan: front (SC530) or rear (SC531). 3. Replace the DRB. 4. Replace the BCU.
Description: Ventilation fan: rear error The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected.
Causes: • Defective ventilation fan: front or rear • Disconnected or defective harness • Defective DRB • Defective BCU
Remedy: 1. Check or replace the harness. 2. Replace the ventilation fan: front (SC530) or rear (SC531). 3. Replace the DRB. 4. Replace the BCU.
Description: Laser unit fan error The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected.
Causes: • Defective laser unit fan • Disconnected or defective harness • Defective drive board • Defective BCU
Remedy: 1. Check or replace the harness. 2. Replace the laser unit fan. Replace the laser unit fan motor. 1. Replace the DRB. 2. Replace the BCU.
Description: Fusing front fan error The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected.
Causes: • Defective fusing front fan • Disconnected or defective harness • Defective DRB • Defective BCU
Remedy: 1. Check or replace the harness. 2. Replace the fusing front fan. 3. Replace the DRB. 4. Replace the BCU.
Description: Fusing rear fan error The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected.
Causes: • Defective fusing rear fan • Disconnected or defective harness • Defective DRB • Defective BCU
Remedy: 1. Check or replace the harness. 2. Replace the fusing rear fan. 3. Replace the DRB. 4. Replace the BCU.
Description: Controller box fan error The motor lock signal error is detected for 10 seconds after the motor lock signal was first detected.
Causes: • Defective controller box fan • Disconnected or defective harness • Defective BCU
Remedy: 1. Check or replace the harness. 2. Replace the controller box fan. 3. Replace the BCU.
Description: Fusing/Paper exit motor error The BCU receives the lock signal 2.0 seconds after turning on the fusing/paper exit motor.
Causes: • Motor overload • Defective fusing/paper exit motor • Defective or disconnected connection for the fusing/paper exit motor
Remedy: 1. Replace the fusing/paper exit motor. 2. Check or replace connector and harness for the fusing/paper exit motor.