Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC5000 — Trang 9/25

Code: 442

Description: Image transfer belt contact motor error
The image transfer belt contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates.
Causes: • Dirty image transfer belt contact sensor • Defective image transfer belt contact motor • Disconnected connector of image transfer belt contact sensor or motor • Disconnected cable
Remedy: 1. Replace the image transfer belt contact sensor. 2. Replace the image transfer belt contact motor.

Code: 443

Description: Image transfer unit error
The machine detects the encoder sensor error.
Causes: • Defective encoder sensor • Image transfer unit installation error • Defective image transfer unit motor
Remedy: 1. Check if the image transfer unit is correctly set. 2. Replace the image transfer unit motor. 3. Replace the image transfer unit.

Code: 452

Description: Paper transfer unit contact error
The paper transfer unit contact sensor does not detect the movement of actuator at the sensor while the polygon motor rotates.
Causes: • Defective paper transfer unit contact sensor • Defective paper transfer unit contact motor • Broken +24V fuse on PSU • Defective IOB
Remedy: 1. Check the connection between the paper transfer unit and PSU. 2. Replace the paper transfer unit contact sensor. 3. Replace the paper transfer unit contact motor. 4. Replace the +24V fuse on the PSU. 5. Replace the IOB.

Code: 460

Description: Separation power pack output error
An interrupt checks the status of the power pack every 20 ms. This SC is issued if the BICU detects a short in the power pack 10 times at D(ac).
Causes: • Damaged insulation on the high-voltage supply cable • Damaged insulation around the high-voltage power supply.
Remedy: 1. Replace the high-voltage supply cable. 2. Replace the high-voltage power supply unit. 3. Replace the IOB.

Code: 490

Description: Toner transport motor error
The LOCK signal is not detected for 2 seconds when the transport motor turns on.
Causes: • Toner transport motor overload • Disconnected or broken harness • Defective toner transport motor • Opened +24V fuse on the PSU • Defective interlock switch
Remedy: 1. Check or replace the harness. 2. Replace the toner transport motor. 3. Replace the +24V fuse on the PSU. 4. Replace the interlock switch.

Code: 491

Description: High voltage power: Drum/ development bias output error
An error signal is detected for 0.2 seconds when charging the drum or development.
Causes: • High voltage leak • Broken harness • Defective drum unit or development unit • Defective high voltage supply unit
Remedy: 1. Check or replace the harness. 2. Replace the drum unit or paper transfer unit. 3. Replace the high voltage supply unit.

Code: 492

Description: High voltage power: Image transfer/ paper transfer bias output error
An error signal is detected for 0.2 seconds when charging the separation, image transfer bet or paper transfer roller.
Causes: • High voltage leak • Broken harness • Defective image transfer belt unit or paper transfer unit • Defective high voltage supply unit
Remedy: 1. Check or replace the harness. 2. Replace the image transfer belt unit or paper transfer unit. 3. Replace the high voltage supply unit.

Code: 498

Description: Temperature and humidity sensor error 2
• The thermistor output of the temperature sensor was not within the prescribed range (0.5V to 4.2V). • The thermistor output of the humidity sensor was not within the prescribed range (0.01V to 2.4V).
Causes: • Temperature and humidity sensor harness disconnected, loose, defective • Temperature and humidity sensor defective
Remedy: 1. Check the connector and harness. 2. Replace the temperature/humidity sensor.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie