Mã lỗi Ricoh Aficio MPC5002 — Trang 11/28
Code:
Tất cả lỗi (217)
101
120
121
141
142
144
161-001
161-002
165
195
202
203
204
210-01
210-02
210-03
210-04
220-01
220-02
220-03
220-04
230-01
230-02
230-03
230-04
231-01
231-02
231-03
231-04
240-01
240-02
240-03
240-04
270
285
312-01
312-02
312-03
312-04
360-01
360-02
360-03
360-04
361-01
361-02
361-03
361-04
362-01
362-02
362-03
362-04
370
390-01
390-02
390-03
390-04
396-01
396-02
396-03
396-04
441
442
443
452
460
490
491
492
498
501
502
503
504
505
520-01
520-02
530
531
532-01
532-02
533-01
534-01
535
538
540
541
542
543
544
545
547
549
551
552
553
554
555
557
559
561
562
563
564
569-00
569-01
571-00
572-02
573
574
581
591
610
620
621
622
623
632
633
634
635
636-01
636-02
636-11
637
640
641
650
651
652
653
670
672
681
682
687
720-24
720-25
720-30
720-41
720-42
720-44
720-52
720-53
720-58
720-59
720-70
720-71
720-80
720-81
722-10
722-14
722-17
724-31
724-32
724-33
724-38
724-41
724-42
724-44
724-70
724-85
770
791
792
816
817
819
821
822
823
824
833
834
838
840
841
842
850
851
853
854
855, 856
858
859
860
861
862
863
864
865
866
867
868
870
872
873
874
875
876
877
878
880
881
899
900
910...915
919
920
921
925
990
991
992
994
995
997
998
Description: Second duct fan error 1 The machine does not detect the fan motor lock signal for 100 ms while the second duct fan turns on.
Causes: • Disconnected harness • Overload on the second duct fan motor • Defective second duct motor • Defective IOB
Remedy: 1. Check or replace the harness. 2. Replace the second duct fan. 3. Replace the IOB.
Description: Third duct fan error The machine does not detect the fan motor lock signal for 100 ms while the third duct fan turns on.
Causes: • Disconnected harness • Overload on the third duct fan motor • Defective third duct motor • Defective IOB
Remedy: 1. Check or replace the harness. 2. Replace the third duct fan. 3. Replace the IOB.
Description: Paper exit fan error The machine does not detect the fan motor lock signal for 100 ms while the paper exit fan turns on.
Causes: • Disconnected harness • Overload on the paper exit fan motor • Defective paper exit motor • Defective IOB
Remedy: 1. Check or replace the harness. 2. Replace the paper exit fan. 3. Replace the IOB.
Description: AC controller board fan error The machine does not detect the fan motor lock signal for 100 ms while the AC controller board fan turns on.
Causes: • Disconnected harness • Overload on the AC controller board fan motor • Defective AC controller board fan motor • Defective IOB
Remedy: 1. Check or replace the harness. 2. Replace the AC controller board fan. 3. Replace the IOB.
Description: Fusing/Paper exit motor error The IOB does not receive the lock signal 100 ms after turning on the fusing/ paper exit motor.
Causes: • Motor overload • Defective fusing/paper exit motor • Shorted +24V fuse on the PSU
Remedy: 1. Check or replace the harness. 2. Replace the fusing/paper exit motor. 3. Replace the +24V fuse on the PSU.
Description: Heating roller thermopile error The temperature detected by the heating roller thermopile does not reach 0°C for 6 seconds.
Causes: • Loose connection of the heating roller thermopile • Defective heating roller thermopile • Defective thermopile
Remedy: 1. Check if the heating roller thermopile is firmly connected. 2. Replace the heating roller thermopile.
Description: Heating roller warm-up error 1 • The heating roller temperature does not reach 80°C for 20 seconds after the inverter turned on. • The center temperature of the heating roller does not reach the ready temperature for 90 seconds after the fusing lamp turned on.
Causes: • Dirty or defective thermopile
Remedy: 1. Check if the heating roller thermopile is firmly connected. 2. Replace the thermopile.
Description: Heating roller overheat: Center (software error) The detected fusing temperature stays at 215°C for 1 second for 10 consecutive times.
Causes: • Defective AC controller board • Defective IOB • Defective IPU
Remedy: 1. Replace the AC controller board. 2. Replace the IOB. 3. Replace the IPU.