Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC6502SP — Trang 44/63

Code: SC701-02

Description: Original pick-up motor driver error (1-pass ADF) Motor driver IC error flag was asserted when a jam occurred. Details: The protection mechanism of the motor driver IC detected overcurrent or overheat and output an error.
Causes: Motor driver IC detected an error.
Remedy: • Check the motor harness connection. • Check for torn paper on the paper path or foreign objects in the drive area. • Replace the motor harness. • Replace the motor. • Replace the board.

Code: SC702-04

Description: Protection device break error 4 (1-pass ADF) The non-interlock power supply system protection device broke the circuit with the 24V power supply on. Details: A motor defect or a short circuit occurred in either the pick-up motor, transmission stamp, or bottom plate lift motor and the non-interlock power system protection device broke the circuit.
Causes: • Motor defect in non-interlock power supply system. • Harness broken
Remedy: • Replace the pick-up motor, transmission stamp solenoid, or bottom plate lift motor. • Replace the harness of pick-up motor, transmission stamp solenoid, or bottom plate lift motor. • Replace the board.

Code: SC702-05

Description: Protection device break error 5 (1-pass ADF) The non-interlock power supply system protection device broke the circuit with the 24V power supply on. Details: A motor defect or a short circuit occurred in either the feed motor, pull-out motor, intermediate motor, scanning motor, or exit motor and the noninterlock power system protection device broke the circuit.
Causes: • Motor defect in non-interlock power supply system. • Harness broken
Remedy: • Replace the feed motor, pull-out motor, intermediate motor, scanning motor, or exit motor. • Replace the harness of feed motor, pull-out motor, intermediate motor, scanning motor, or exit motor. • Replace the board.

Code: SC719-07

Description: Downstream device communication error (D751) • Communication with the downstream device has established, but the device is not responding to the command sent out, even after being sent three times. • The port level of the downstream device does not become H level (break cancel) within specified time.
Causes: • Interface cable (downstream device side) connector disconnected or broken • Board defective (Buffer pass unit or downstream device)
Remedy: • Replace the interface cable between buffer pass unit and downstream device or reconnect the connectors. • Replace the board (of the buffer pass unit or downstream device).

Code: SC719-08

Description: Buffer pass unit_CTB_+24V_Power supply error Detected +24V power OFF of the Buffer pass unit PCB: CTB.
Causes: • Buffer pass unit PSU defect • Connecter disconnected • Harness ground fault/broken • 24V load (motor/fan) layer short • PCB defective • Fuse tripped (PSU, PCB)
Remedy: • Replace the Buffer pass unit PSU. • Reconnect the connector. • Replace the harness. • Replace the motor/fan. • Replace the PCB.

Code: SC719-09

Description: Buffer pass unit_CTB_+24VINT_Power supply error Detected +24VINT power OFF of the Buffer pass unit PCB: CTB.
Causes: • Buffer pass unit PSU defect • Connecter disconnected • Harness ground fault/broken • 24V load (motor/fan) layer short • PCB defective • Fuse tripped (PSU, PCB) • PCB relay defect
Remedy: • Replace the Buffer pass unit PSU. • Reconnect the connector. • Replace the harness. • Replace the motor/fan. • Replace the PCB.

Code: SC720-01

Description: Downstream device communication error (D703/D704) Communication with the downstream device has established, but the device is not responding to the command sent out, even after being sent three times.
Causes: • Interface cable (downstream device side) connector disconnected or broken • PCB of downstream device defective • Controller PCB defective
Remedy: • Replace the controller board. • Replace the PCB of downstream device. • Replace the interface cable.

Code: SC720-03

Description: Protection device break error 1 (D703/D704) Protection device break error (fuse tripped)
Causes: • Short-circuit • Overload • Motor/solenoid defective
Remedy: • Check the harness. • Replace the PCB/motor/solenoid.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie