Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC8002SP — Trang 3/63

Code: SC195-00

Description: Machine serial number error Comparison of the product identification code in the machine serial number (11 digits).
Causes: The product identification code in the machine serial number (11 digits) does not match.
Remedy: Re-enter the machine serial number.

Code: SC202-01

Description: Polygon Motor: ON Timeout Error: Bk. After the polygon motor turned on, or within 10 sec. after the rpm’s changed, the motor did not enter READY status.
Causes: • The interface harness to the polygon motor driver damaged or not connected correctly. • Polygon motor or polygon motor driver defective • Polygon motor drive pulse cannot be output correctly. (Polygon controller) • XSCRDY signal observation failing (Polygon controller)
Remedy: • Cycle the machine off/on. • Replace the LSU. • Replace the polygon harness. • Replace the IPU board.

Code: SC202-03

Description: Polygon Motor: ON Timeout Error: Ma. After the polygon motor turned on, or within 10 sec. after the rpm’s changed, the motor did not enter READY status.
Causes: • The interface harness to the polygon motor driver damaged or not connected correctly. • Polygon motor or polygon motor driver defective • Polygon motor drive pulse cannot be output correctly. (Polygon controller) • XSCRDY signal observation failing (Polygon controller)
Remedy: • Cycle the machine off/on. • Replace the LSU. • Replace the polygon harness. • Replace the IPU board.

Code: SC203-01

Description: Polygon Motor: OFF Timeout Error: Bk. The XSCRDY signal (polygon ready) never becomes inactive (H) after the polygon motor went OFF.
Causes: • The interface harness to the polygon motor driver damaged or not connected correctly. • Polygon motor or polygon motor driver defective • Polygon motor drive pulse cannot be output correctly. (Polygon controller) • XSCRDY signal observation failing (Polygon controller)
Remedy: • Cycle the machine off/on. • Replace the LSU. • Replace the polygon harness. • Replace the IPU board.

Code: SC203-03

Description: Polygon Motor: OFF Timeout Error: Ma. The XSCRDY signal (polygon ready) never becomes inactive (H) after the polygon motor went OFF.
Causes: • The interface harness to the polygon motor driver damaged or not connected correctly. • Polygon motor or polygon motor driver defective • Polygon motor drive pulse cannot be output correctly. (Polygon controller) • XSCRDY signal observation failing (Polygon controller)
Remedy: • Cycle the machine off/on. • Replace the LSU. • Replace the polygon harness. • Replace the IPU board.

Code: SC204-01

Description: Polygon Motor: XSCRDY Signal Error: Bk. During polygon motor rotation, the XSCRDY signal was inactive (H) for longer than one rotation of the polygon. Details: • Occurs when the PATMOS polygon error determination register detects that the XSCRDY signal was inactive (H) for longer than one rotation of the polygon (7 cycles of PMCLK). • The PATMOS polygon error determination register detects that the XSCRDY signal was inactive (H) for longer than one rotation of the polygon, and then refers to SCERR2.
Causes: • Polygon motor or polygon motor driver defective • The interface harness to the polygon motor driver damaged or not connected correctly.
Remedy: • Cycle the machine off/on. • Replace the LSU. • Replace the polygon harness.

Code: SC204-03

Description: Polygon Motor: XSCRDY Signal Error: Ma. During polygon motor rotation, the XSCRDY signal was inactive (H) for longer than one rotation of the polygon. Details: • Occurs when the PATMOS polygon error determination register detects that the XSCRDY signal was inactive (H) for longer than one rotation of the polygon (7 cycles of PMCLK). • The PATMOS polygon error determination register detects that the XSCRDY signal was inactive (H) for longer than one rotation of the polygon, and then refers to SCERR2.
Causes: • Polygon motor or polygon motor driver defective • The interface harness to the polygon motor driver damaged or not connected correctly.
Remedy: • Cycle the machine off/on. • Replace the LSU. • Replace the polygon harness.

Code: SC210-01

Description: Trailing Edge Beam Error: Bk. When the main scan magnification rate was measured, the value measured between 2 points was out of specification. Details: • When a trailing edge beam detection error flag is asserted to VTEC status register. • The CPU detected an error flag when measuring the main scan magnification rate.
Causes: • The interface harness to the beam detection unit damaged or not connected correctly. • Beam detection board defective • Beam does not enter photodetector. • Abnormality around VTEC • LDB defective • BCU defective • Large main scan magnification rate
Remedy: • Cycle the machine off/on. • Replace the LSU board. • Replace the IPU board. • Replace the BCU board. • Correct the main scan magnification SP* * SP2-184-006 through 009 = 269600 SP2-102-001,007 = 123 SP2-102-016 through 025 = 0 Adjust SP2-184-006 through 009 while checking the images until the values of SP2-102-001,007 become 123 ± 30.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie