Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio MPC8002SP — Trang 6/63

Code: SC240-03

Description: LD error: Ma. When two errors were detected consecutively while monitoring the VTEC for LD error registers in 350msec intervals after LD initialization. Details: The VTEC LD error flag was detected twice consecutively when the LD turned on after initialization.
Causes: • LD degradation (LD broken, shift of output characteristics etc.) • LD driver defective • VTEC defective • The interface harness damaged or not connected correctly. • Large main scan magnification rate
Remedy: • Cycle the main power off/on. • Replace the IPU board. • Replace the LSU board. • Replace the LD unit. • Replace the harness. • Correct the main scan magnification SP* * SP2-184-006 through 009 = 269600 SP2-102-001,007 = 123 SP2-102-016 through 025 = 0 Adjust SP2-184-006 through 009 while checking the images until the values of SP2-102-001,007 become 123 ± 30.

Code: SC260-01

Description: Laser Thermistor Error: Bk. • The reading of the thermistor in the laser unit was less than 10 °C (50 °F), indicating that the thermistor has disconnected. • The reading of the thermistor in the CK or YM laser unit was more than 80 °C (176 °F), indicating that the thermistor has shorted out. Details: When the thermistor voltage is out of range (-10 to 80 °C) after the machine was turned on.
Causes: • Thermistor defective • Harness defective • BCU defective
Remedy: • Cycle the machine off/on. • Replace the LSU board. • Replace the LSU harness.

Code: SC260-03

Description: Laser Thermistor Error: Ma. • The reading of the thermistor in the laser unit was less than 10 °C (50 °F), indicating that the thermistor has disconnected. • The reading of the thermistor in the CK or YM laser unit was more than 80 °C (176 °F), indicating that the thermistor has shorted out. Details: When the thermistor voltage is out of range (-10 to 80 °C) after the machine was turned on.
Causes: • Thermistor defective • Harness defective • BCU defective
Remedy: • Cycle the machine off/on. • Replace the LSU board. • Replace the LSU harness.

Code: SC265-02

Description: Skew correction error: Cy. The skew control pulse total is not within range.
Causes: • Skew motor defective • Harness defective • Optical system defective
Remedy: • Cycle the machine off/on. • Replace the LSU board. • Replace the LSU harness.

Code: SC265-03

Description: Skew correction error: Ma. The skew control pulse total is not within range.
Causes: • Skew motor defective • Harness defective • Optical system defective
Remedy: • Cycle the machine off/on. • Replace the LSU board. • Replace the LSU harness.

Code: SC265-04

Description: Skew correction error: Ye. The skew control pulse total is not within range.
Causes: • Skew motor defective • Harness defective • Optical system defective
Remedy: • Cycle the machine off/on. • Replace the LSU board. • Replace the LSU harness.

Code: SC270-01

Description: LD ASIC communication error: Bk. On startup: Written to and read the same register but the values were different. VTEC: Monitored the parity and retried three times. Details: • On startup: Data 0x5A5A and 0xA5A5 are written to a predetermined register. Then the register is read and the read data is compared to the are compared • VTEC: Monitors parity during communication. If it does not match, retries up to three times. The second retry constitutes an SC.
Causes: • VTEC defective • HORUS defective • BCU defective • IPU defective • Harness defective
Remedy: • Cycle the machine off/on. • Replace the LSU board. • Replace the IPU board. • Replace the BCU board. • Replace the LDB harness.

Code: SC270-03

Description: LD ASIC communication error: Ma. On startup: Written to and read the same register but the values were different. VTEC: Monitored the parity and retried three times. Details: • On startup: Data 0x5A5A and 0xA5A5 are written to a predetermined register. Then the register is read and the read data is compared to the are compared • VTEC: Monitors parity during communication. If it does not match, retries up to three times. The second retry constitutes an SC.
Causes: • VTEC defective • HORUS defective • BCU defective • IPU defective • Harness defective
Remedy: • Cycle the machine off/on. • Replace the LSU board. • Replace the IPU board. • Replace the BCU board. • Replace the LDB harness.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie