• Code: 790
• Description: Jogger Fence Motor Error: Booklet Finisher B836 The jogger fence HP sensor failed to detect the jogger fence at the home position within the specified time.
• Causes: If the jogger fence motor is operating: • Jogger fence HP sensor harness loose, broken, defective • Jogger fence HP sensor defective If the jogger fence motor is not operating: • Motor blocked by an obstruction • Motor harness loose, broken, defective • Motor defective • Finisher main board defective
• Remedy: 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the jogger fence HP sensor. 4. Replace the jogger fence motor. 5. Replace the finisher main board.

• Code: 791
• Description: Feed Out Belt Motor Error: Booklet Finisher B836 The stack feed out belt HP sensor failed to detect the feed out belt at the home position within the specified time.
• Causes: If the feed out belt motor is operating: • Stack feed out belt HP sensor harness loose, broken, defective • Stack feed out belt HP sensor defective If the feed out belt motor is not operating: • Motor blocked by an obstruction • Motor harness loose, broken, defective • Motor defective • Finisher main board defective
• Remedy: 1. Check or clear obstacles around the motor drive mechanism. 2. Check the harness connection. 3. Replace the stack feed out belt HP sensor. 4. Replace the feed out belt motor. 5. Replace the finisher main board.

• Code: 792-1
• Description: Ring Binder (D392) Junction gate error Detected at HP after the time prescribed to leave the HP had elapsed (more than 36 pulses) (1 detection, jam, twice detected, SC error) -or- Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 22 pulses) (1 detection, jam, twice detected, SC error)
• Causes: • Path JG motor (M201) defective • Motor connector loose, broken, defective • Motor overload • Path JG sensor (S203) connector loose, broken, defective • Sensor (S203) defective
• Remedy:

• Code: 792-10
• Description: Ring Binder (D392) Binder unit runout error Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error) -or- Detected at HP after the time prescribed to leave the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error)
• Causes: • Runout press roller motor (M610) connector loose, broken, defective • Motor defective • Motor overload • Runout roller HP sensor (S614) connector loose, broken, defective • Sensor defective
• Remedy:

• Code: 792-11
• Description: Ring Binder (D392) Clamp thickness error 50-sheet detection sensor (S606) went OFF during pre-bind jogging when a 100-sheet thickness was detected. (1st detection jam, 2nd detection SC error) -or- 50-sheet detection sensor went OFF at initialization when the clamp moved to the open position.
• Causes: • 50-sheet detection sensor (S606) connector loose, broken, defective • Sensor defective
• Remedy:

• Code: 792-12
• Description: Ring Binder (D392) Alignment pin error Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error) -or- Detected at HP after the time prescribed to leave the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error)
• Causes: • Alignment pin motor (M602) connector loose, broken, defective • Motor overload • Motor defective • Alignment pin HP sensor (S604) connector loose, broken, defective • Sensor defective
• Remedy:

• Code: 792-13
• Description: Ring Binder (D392) Pre-bind jogger shutter error Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error) -or- Detected at HP after the time prescribed to leave the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error)
• Causes: • Shutter motor (M608) connector loose, broken, defective • Motor overload • Motor defective • Shutter HP sensor (S605) connector loose, broken, defective • Sensor defective
• Remedy:

• Code: 792-14
• Description: Ring Binder (D392) 50/100 clamp adjustment error Not detected at HP after the time prescribed to arrive at the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error) -or- Detected at HP after the time prescribed to leave the HP had elapsed (more than 400 ms) (1st detection, jam, 2nd detection, SC error)
• Causes: • 50/100 adjustment motor (M702) connector loose, broken, defective • Motor overload • Motor defective • Ring switch HP sensor (S706) connector loose, broken, defective, or sensor defective • Ring switch timing sensor (S707) connector loose, broken, defective, or sensor defective
• Remedy: