Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SP5210DN — Trang 4/10

Code: 557

Description: Zero cross frequency error
Zero cross signals of wavelength 50-60 Hz were not detected within 5 seconds after the fusing relay switched on.
Causes: AC line noise (High frequency)
Remedy: • No action needed. • This SC will perform logging only. The machine will start up normally.

Code: 559

Description: Fuser 3 times jam error
The paper jam counter for the fusing unit reaches 3. The paper jam counter is cleared if the paper is fed correctly. This SC is activated only when this function is enabled with "Engine Maintenance" (default "OFF").
Causes: Paper jams at the fusing roller
Remedy: • This SC cannot be reset by turning the power off and on. • This SP should be reset by a CE. • SP1159 determines whether SC559 is issued. The default is off. SC559 is not issued after three consecutive jams in the paper unit. If SP1159 is set to on, turning the machine power off/on does not reset the jam counter.

Code: 622

Description: Paper tray unit communication error bank 1
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication.
Causes: 1. Disconnect harnesses 2. Defective Paper tray unit 3. Defective engine board 4. External noise
Remedy: • Turn the Power Switch Off and On. • Connect the harnesses properly. • Replace the Paper tray unit. • Replace the engine board.

Code: 623

Description: Paper tray unit communication error bank 2
Three consecutive errors occur during poll`ing, after the paper tray unit has successful I2C communication.
Causes: Turn the Power Switch Off and On. Connect the harnesses properly. Replace the Paper tray unit.
Remedy: • Turn the Power Switch Off and On. • Connect the harnesses properly. • Replace the Paper tray unit.

Code: 624

Description: Paper tray unit communication error bank 3
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication.
Causes: Disconnect harnesses. Defective Paper tray unit. External noise
Remedy: • Turn the Power Switch Off and On. • Connect the harnesses properly. • Replace the Paper tray unit.

Code: 625

Description: Paper tray unit communication error bank 4
Three consecutive errors occur during polling, after the paper tray unit has successful I2C communication.
Causes: Disconnect harnesses. Defective Paper tray unit. External noise
Remedy: • Turn the Power Switch Off and On. • Connect the harnesses properly. • Replace the Paper tray unit.

Code: 641

Description: Engine-Controller Communication Error: Non-Response
There was no response to a frame sent from the controller board to the engine. There is still no response after resending frames 3 times in 100 milliseconds
Causes: Engine board defective. Engine board harness loose, broken, defective. External noise
Remedy: 1. Turn the machine power Off and On. 2. Keep away from noise sources. 3. Replace the engine board harness. 4. Replace the engine board.

Code: 669

Description: EEPROM communication error
The EEPROM was not connected at power on, or read/write operations on the EEPROM failed. Retrying 3 times after the error detection cannot recover from the error.
Causes: External noise. Defective EEPROM
Remedy: • Turn the Power Switch Off and On. • Replace the engine board (Replace the EEPROM).
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie