Description: TD sensor (Vt low) error 2: M. The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) ten counts.
Remedy: 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and development unit for damage. 2. Check the drawer connector of the PCDU. 3. Replace the PCDU.
Description: TD sensor (Vt low) error 2: C. The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) ten counts.
Remedy: 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and development unit for damage. 2. Check the drawer connector of the PCDU. 3. Replace the PCDU.
Description: TD sensor (Vt low) error 2: Y. The Vt value of the black, magenta, cyan, or yellow TD sensor is below the specified value with SP3020-004 (default: 0.5V) ten counts.
Remedy: 1. Check the black, magenta, cyan, or yellow TD sensor connector and harness between the TD sensor and development unit for damage. 2. Check the drawer connector of the PCDU. 3. Replace the PCDU.
Description: TD sensor adjustment error: K. SC is issued only if one of followings is satisfied. • During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.5V) ± 0.2V. • The TD sensor output is 0.7 V or more when the Vcnt is 4.3 v. • The adjusted Vcnt is 4.7 V or less.
Causes: • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective • Different developer density from initial developer density
Remedy: 1. Remove the heat seal from each PCDU. 2. Replace the PCDU.
Description: TD sensor adjustment error: M SC is issued only if one of followings is satisfied. • During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.5V) ± 0.2V. • The TD sensor output is 0.7 V or more when the Vcnt is 4.3 v. • The adjusted Vcnt is 4.7 V or less.
Causes: • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective • Different developer density from initial developer density
Remedy: 1. Remove the heat seal from each PCDU. 2. Replace the PCDU.
Description: TD sensor adjustment error: C. SC is issued only if one of followings is satisfied. • During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.5V) ± 0.2V. • The TD sensor output is 0.7 V or more when the Vcnt is 4.3 v. • The adjusted Vcnt is 4.7 V or less.
Causes: • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective • Different developer density from initial developer density
Remedy: 1. Remove the heat seal from each PCDU. 2. Replace the PCDU.
Description: TD sensor adjustment error: Y. SC is issued only if one of followings is satisfied. • During TD sensor initialization, the output value of the black, magenta, cyan, or yellow TD sensor is not within the range of the specified value with SP3238-001 to -004 (default: 2.5V) ± 0.2V. • The TD sensor output is 0.7 V or more when the Vcnt is 4.3 v. • The adjusted Vcnt is 4.7 V or less.
Causes: • Heat seal not removed from a new developer pack • TD harness sensor disconnected, loose or defective • TD sensor defective • Harness between TD sensor and drawer disconnected, defective • Different developer density from initial developer density
Remedy: 1. Remove the heat seal from each PCDU. 2. Replace the PCDU.
Description: Drum gear position sensor error: K. The machine does not detect a change signal (H L or L H) for 2.4 seconds at the drum phase adjustment.
Causes: • Dirty or defective drum gear position sensor
Remedy: 1. Check the harnesses. 2. Clean or replace the drum gear position sensor. 3. Replace the PCDU.
Nhận ưu đãi sớm nhất khi chương trình diễn ra
Đăng ký nhận bản tin
Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này.
Chính sách cookie
Những cookie này là cần thiết để trang web hoạt động đúng cách.
Những cookie này giúp chúng tôi hiểu cách khách truy cập tương tác với trang web.
Những cookie này được sử dụng để cung cấp quảng cáo cá nhân hóa.