Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh Aficio SPC811DN — Trang 12/23

Code: 547

Description: Zero cross error
• The zero cross signal is detected three times even though the heater relay is off when turning on the main power. • The zero cross signal is not detected for 3 seconds even though the heater relay is on after turning on the main power or closing the front door. • The detection error occurs twice or more in the 11 zero cross signal detections. This error is defined when the detected zero cross signal is less than 39.
Causes: • Defective fusing relay • Defective fusing relay circuit • Shorted +24V fuse on the PSU • Unstable power supply
Remedy: 1. Check the power supply source. 2. Replace the +24V fuse on the PSU. 3. Replace the PSU

Code: 548

Description: Fusing unit rotation error
The fusing belt sensor does not detect change in the actuator for 0.5 seconds after the fusing/paper exit motor has turned on.
Causes: • Defective fusing/paper exit motor • Deformed actuator for the fusing belt sensor • Defective fusing belt sensor • Broken connection between IH inverter and IOB • Incorrectly set fusing unit
Remedy: 1. Check if the fusing unit is correctly set. 2. Check or replace the actuator for fusing belt sensor. 3. Replace the fusing belt sensor. 4. Replace the IH inverter. 5. Check the connection between IH inverter and IOB.

Code: 549

Description: Ferrite core rotation error
The ferrite roller HP sensor does not detect the ferrite roller home position for 4 seconds after the fusing/paper exit motor has turned on.
Causes: • Deformed actuator for the ferrite roller HP sensor • Defective ferrite roller HP sensor • Defective ferrite roller motor • Shorted +24V fuse on the PSU • Defective IOB
Remedy: 1. Replace the heating roller. 2. Replace the ferrite roller HP sensor. 3. Replace the ferrite roller motor. 4. Replace the +24V fuse on the PSU. 5. Replace the IOB.

Code: 551

Description: Heating roller thermistor error
The temperature measured by the heating roller thermistor does not reach 0 °C for 7 seconds.
Causes: • Loose connection of heating roller thermistor • Defective heating roller thermistor
Remedy: 1. Check that the heating roller thermistor is firmly connected. 2. Replace the heating roller thermistor.

Code: 552

Description: Heating roller warm-up error 2
• The heating roller temperature does not reach the ready temperature for 90 seconds after the heating lamp on. • The heating roller temperature does not reach 80°C for 13 seconds after the IH inverter on.
Causes: • Defective thermistor • Defective IH inverter
Remedy: 1. Check if the heating roller thermistor is firmly connected. 2. Replace the IH inverter.

Code: 553

Description: Heating roller overheat (software error)
The detected heating roller temperature stays at 230°C or more for 1 second.
Causes: • Defective PSU • Defective IOB • Defective EGB
Remedy: 1. Replace the PSU. 2. Replace the IOB. 3. Replace the EGB.

Code: 554

Description: Heating roller overheat (hardware error)
The heating roller thermistor detects 240°C or more.
Causes: • Defective PSU • Defective IOB • Defective EGB • Defective fusing control system
Remedy: 1. Replace the PSU. 2. Replace the IOB. 3. Replace the EGB.

Code: 557

Description: Zero cross frequency error
When the zero cross signal is 66 or more and it is detected 10 times or more in 11 detections, the machine determines that input 60 Hz and SC557 occurs.
Causes: • Noise (High frequency)
Remedy: 1. Check the power supply source.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie