Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh B234 MP9000 B-C3 — Trang 4/25

Code: SC202

Description: Polygon Motor Error 1: ON Timeout
The polygon mirror motor did not reach its operating speed within 20 s after the polygon motor switched on.
Causes: • Connection between the polygon mirror motor control board and the motor is loose, broken, or defective
• Polygon mirror motor defective
• Polygon mirror motor control board defective
• IPU defective
• BCU defective

Code: SC203

Description: Polygon Motor Error 2: OFF Timeout
The polygon mirror motor did not go off within 3 s after the motor was switched off.
Causes: • Connection between the polygon mirror motor control board and the motor is loose, broken, or defective
• Polygon mirror motor defective
• Polygon mirror motor control board defective
• IPU defective
• BCU defective

Code: SC204

Description: Polygon Motor Error 3: XSCRDY Signal Error
The machine detected that the polygon mirror motor XSCRDY signal went inactive :
• While an image was being created
• During the output of a synchronous laser detection signal
Causes: • Switch the machine off/on (problem was probably due to electronic noise)
• Replace the harness if cycling the machine off/on does not solve the problem
• Polygon motor defective
• Polygon mirror motor control board defective
• IPU defective
• BCU defective

Code: SC205

Description: Polygon Motor Error 4: Unstable Timeout
The machine detected that the polygon mirror motor signal went inactive at some time other than: • While an image was being created • During the output of a synchronous laser detection signal
Causes: • Switch the machine off/on (problem was probably due to electronic noise)
• Replace the harness if cycling the machine off/on does not solve the problem
• Polygon motor defective
• Polygon mirror motor control board defective
• IPU defective

Code: SC220

Description: Synchronization Detector Error 1: LD0
When LD0 fired with the polygon mirror motor rotating at normal speed, an synchronous detection signal was not output within 250 ms.
Causes: • Cycle the machine off/on
• Harness connector of the laser synchronization detector board is loose, broken, defective
• Laser synchronization detection board defective or installed improperly
• LD unit defective
• IPU defective
• BCU defective

Code: SC221

Description: Synchronization Detection Error 2: Other Than LD0
When a laser diode (other than LD0) fired with the polygon mirror motor rotating at normal speed, an synchronous detection signal was not output within 250 ms.
Causes: • Cycle the machine off/on
• Harness connector of the laser synchronization detector board is loose, broken, defective
• Laser synchronization detection board defective or installed improperly
• LD unit defective
• IPU defective
• BCU defective

Code: SC230

Description: FGATE Error 1: Signal Failed to Turn On
The FGATE signal did not switch on within 1 s of when the lasers were supposed to start writing the image.
Causes: • Cycle the machine off/on
• Check the harnesses, connectors of the IPU, Controller, BCU
• GAVD on the IPU board defective
• Controller defective
• BCU defective

Code: SC231

Description: FGATE Error 2: Signal Failed to Turn Off
The FGATE signal did not switch off within 7 s of when the lasers started writing the image, or remained off at the beginning of the next job.
Causes: • Cycle the machine off/on
• Check the harnesses, connectors of the IPU, Controller, BCU
• GAVD on the IPU board defective
• Controller defective
• BCU defective
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie