Thương hiệu phân phối chính hãng
Giỏ hàng

Mã lỗi Ricoh D121 MP2852 — Trang 2/22

Code: 165

Description: Copy Data Security Unit error
• The copy data security board is not detected when the copy data security function is set "ON" with the initial setting. • A device check error occurs when the copy data security function is set "ON" with the initial setting.
Causes: • Incorrect installation of the copy data security board • Defective copy data security board
Remedy: 1. Reinstall the copy data security board. 2. Replace the copy data security board.

Code: 195

Description: Serial Number Mismatch
• Serial number stored in the memory does not have the correct code.
Causes: • NVRAM defective • BCU replaced without original NVRAM
Remedy: 1. Check the serial number with SP5-811-002. 2. If the stored serial number is incorrect, contact your supervisor.

Code: 202

Description: Polygon motor error 1: ON timeout
The polygon mirror motor did not reach the targeted operating speed within 10 sec. after turning on or changing speed
Causes: • Polygon motor/driver board harness loose or broken • Polygon motor/driver board defective • Laser optic unit defective • IPU defective
Remedy: 1. Replace the polygon motor. 2. Replace the laser optics housing unit. 3. Replace the harness. 4. Replace the IPU.

Code: 203

Description: Polygon motor error 1: OFF timeout
The polygon mirror motor did not leave READY status within 3 sec. after polygon motor switched off.
Causes: • Polygon motor/driver board harness loose or broken • Polygon motor/driver board defective • Laser optic unit defective • IPU defective
Remedy: 1. Replace the polygon motor. 2. Replace the laser optics housing unit. 3. Replace the harness. 4. Replace the IPU.

Code: 204

Description: Polygon motor error 1: XSCRDY signal error
The XSCRDY signal remained HIGH for 200 ms while the LD unit was firing.
Causes: • Polygon motor/driver board harness loose or broken • Polygon motor/driver board defective • Laser optic unit defective • IPU defective
Remedy: 1. Replace the polygon motor. 2. Replace the laser optics housing unit. 3. Replace the harness. 4. Replace the IPU.

Code: 220

Description: Laser synchronization detection error: LD0
The laser synchronizing detection signal for the start position of the LD was not output for two sec. after LDB unit turned on with the polygon motor rotating normally.
Causes: • Laser synchronizing detection board harness loose or broken. • Laser synchronization detection board defective • LDB unit defective • IPU defective
Remedy: 1. Check the connectors. 2. Replace the laser-synchronizing detector. 3. Replace the LDB. 4. Replace the IPU.

Code: 230

Description: FGATE ON error
The FGATE signal did not assert within the prescribed time. (The BCU generates the FGATE signal and sends it to the LD unit when the registration sensor switches on.)
Causes: • BCU, Controller board harness loose or broken • BCU defective • Controller board defective
Remedy: 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.

Code: 231

Description: FGATE OFF error
The FGATE signal did not go off within the prescribed time. (The BCU generates the FGATE signal and sends it to the LD unit when the registration sensor switches on.)
Causes: • BCU, Controller board harness loose or broken • BCU defective • Controller board defective
Remedy: 1. Check the connection between the controller board and the BCU. 2. Replace the BCU. 3. Replace the controller board.
Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin Đăng ký nhận bản tin
Đăng ký nhận bản tin
Nhận ưu đãi sớm nhất khi chương trình diễn ra

Đăng ký nhận bản tin

Việc cho phép sử dụng cookie sẽ giúp cải thiện trải nghiệm của bạn trên trang web này. Chính sách cookie